Maxim Integrated MAX2771 Скачать руководство пользователя страница 1

Страница: 1 / 50

General Description

The MAX2771 is a next-generation Global Navigation

Satellite System (GNSS) receiver covering E5/L5, L2,

E6, E1/L1 bands and GPS, GLONASS, Galileo, QZSS,

IRNSS, and BeiDou navigation satellite systems on a

single chip.
Designed on Maxim’s advanced, low-power SiGe BiCMOS

process technology, the MAX2771 offers the highest

performance and integration at a low cost. Incorporated

on the chip is the complete receiver chain, including

a dual-input LNA and mixer, followed by filter, PGA,

and multi-bit ADC, along with a fractional-N frequency

synthesizer, and crystal oscillator. The total cascaded

noise figure of this receiver is as low as 1.4dB.
The MAX2771 completely eliminates the need for exter-

nal IF filters by implementing on-chip monolithic filters

and requires only a few external components to form a

complete, low-cost GNSS RF receiver solution.
The MAX2771 is the most flexible receiver on the

market. The integrated delta-sigma fractional-N frequency

synthesizer allows programming of the IF frequency within

a ±30Hz (f

XTAL

= 32MHz) accuracy while operating with

any reference or crystal frequencies that are available in

the host system. The ADC outputs CMOS logic levels with

one or two quantized bits for both I and Q channels, or up

to 3 quantized bits for the I channel. The on-chip ADCs

can be bypassed and the analog I and Q signals output

for sampling with external ADCs. An analog monitoring

feature is provided that allows simultaneous output of the

on-chip ADC samples and the I analog signal.
The MAX2771 is packaged in a 5mm x 5mm, 28-pin,

TQFN package with an exposed paddle.

Applications

●

Location-Enabled Mobile Handsets

●

PNDs (Personal Navigation Devices)

●

Telematics (Asset Tracking, Inventory Management)

●

Marine/Avionics Navigation

●

Software GPS

●

Laptops and Netbooks

●

Surveying Equipment

●

Digital Still Cameras and Camcorders

●

Vehicle Tracking and Fleet Management

Ordering Information

appears at end of data sheet.

19-100378; Rev 0; 7/18

Benefits and Features

●

Multi-Constellation Support

• GPS, Galileo, GLONASS, BeiDou, IRNSS, QZSS,

SBAS

●

Multiband Support

• L1, L2, L5, E1, E5, E6, B1, B2, B3

●

Programmable IF Bandwidths of 2.5MHz, 4.2MHz,

8.7MHz, 16.4MHz, 23.4MHz, 36MHz

• Supports Wide-Band Carriers for Precision

Applications (e.g., GPS L5, Galileo E5)

●

Operates in Low IF or Zero IF Mode

• Programmable IF Center Frequency

●

Fractional-N Synthesizer with Integrated VCO

Supports Wide Range of Reference Frequencies

●

On-Chip LNAs to Support Multiple Bands

●

1.4dB Cascaded Noise Figure and 110dB of

Cascaded Gain with Gain Control Range of 59dB

from PGA

●

Integrated Crystal Oscillator

●

Supply Voltage Range: 2.7V to 3.3V

●

28-Pin, RoHS-Compliant, Thin QFN Lead-Free

Package (5mm x 5mm)

Click

here

for production status of specific part numbers.

MAX2771

Multiband Universal GNSS Receiver

EVALUATION KIT AVAILABLE

Содержание MAX2771



















































Результаты поиска

Содержание MAX2771

Отзывы:

Бренды по названию

Популярные бренды

Maxim Integrated MAX2771, Общее описание устройства

Результаты поиска

Содержание MAX2771

Отзывы:

Бренды по названию

Популярные бренды