background image

11

MAXDATA Server PLATINUM 2200 IR M8

2  Server System Features

This chapter briefly describes the main features of the MAXDATA PLATINUM server system. It provides 
a list of the server system features and diagrams showing the location of important components and 
connections on the server system.

Table 3 summarizes the major features of the server system.

Table 3.  Server system features

Feature

Description

Dimensions

 

87.3 mm high

 

430 mm wide

 

704.8 mm deep

 

29 kg max chassis weight

Server board

Intel

®

 S2600GZ/S2600GL

Processor

One or two Intel

®

 Xeon

®

 E5-2600 processors with a thermal design power (TDP) 

of up to 130 W

System memory

•  S2600GL: 16 DIMM slots, 8 per processor, distributed over 4 memory channels
•  S2600GZ: 24 DIMM slots, 12 per processor, distributed over 4 memory channels
•  Up to 768 GB system memory using 32-GB LRDIMMs
•  800/1066/1333/1600 MT/s ECC Unbuffered (UDIMM), Registered (RDIMM) or 

Load-Reduced (LRDIMM) DDR3 memory

•  No mixing of UDIMMs, RDIMMs and LRDIMMs
•  DDR3 standard I/O voltage of 1.5 V and DDR3 Low Voltage of 1.35 V

Chipset

•  Intel

®

 C600 Platform Controller Hub (PCH) with integrated storage controller 

unit (SCU)

•  RAID upgrade keys supported for the SCU ports

Peripheral 
interfaces

External connections:

•  One DB-15 video connector (1 × on back panel + 1 × on front panel with 

configurations up to 8 × 3.5" or 16 × 2.5" HDD)

•  One RJ-45 serial port A connector
•  Four RJ-45 network ports for 10/100/1000 Mbit/s
•  Three USB 2.0 ports on back panel
•  Two USB 2.0 ports on front panel with configurations up to 8 × 3.5" or

 

16 × 2.5" HDD

Internal connections:

•  One USB connector for two USB 2.0 ports
•  One low-profile eUSB connector (2 × 5) for low-profile eUSB SSD
•  One DH-10 connector for serial port B
•  Two SATA III ports (6 Gbit/s)
•  Two quad mini-SAS ports (3 Gbit/s SATA/SAS) (feature activation with RAID 

upgrade keys; four SATA ports enabled by default)

Graphics

•  On-board Matrox G200 2D video controller
•  16 MB graphics memory

LAN

Intel

®

 I350 controller with four ports for 10/100/1000 Mbit/s Ethernet LAN

Expansion 
capabilities

•  Riser 1:
  - 2 × PCIe Gen III x8 with x16 connector from CPU 1
  - 1 × PCIe Gen III x8 from CPU 2
•  Riser 2:
  - 2 × PCIe Gen III x8 with x16 connector from CPU 2
  - 1 × PCIe Gen III x8 from CPU 2
•  One port for optional hardware RAID expansion (SAS ROC)
•  One port for optional I/O expansion (4 × 1-Gbit/s NIC or 2 × 10-Gbit/s NIC or FDR 

Infiniband)

•  Remote Management Module 4 network and feature key ports

Содержание PLATINUM 2200 IR

















































Отзывы: