background image

17

11. Open the drain cock to discharge all the 

compressed air and water in the air tank.

If you found any abnormalities in the check-
up or inspection prior to the operation, send 
the machine to your dealer or authorized 
service facility for inspection or repair.

Operating Procedure

Before operating the machine, be sure to carry 
out the "Inspection and checkup prior to opera-
tion" described on page 15.

1. Fully open the drain cock and turn the 

power switch on. The buzzer will sound 
with a beep at the same time.

For buzzer sounding patterns, see 
page 21.
After the operation has started, close the 
drain cock tight to increase the pressure.

2. After confirming the operation has 

stopped due to the increased pressure, 
turn the adjustment handle of the pres-
sure-reduction valve to adjust the operat-
ing pressure of the nailer and pneumatic 
tool to the appropriate level. When ad-
justing the pressure, turn the pressure-
reduction valve's adjustment handle 
counterclockwise to set the pressure at a 
level lower than the appropriate value by 
2 bars once. Then proceed to the adjust-
ment while increasing the pressure by 
turning the handle clockwise.

Make sure to start the adjustment at a level 
lower than the appropriate pressure and 
continue the adjustment while increasing 
the pressure from that level upward. If you 
start the adjustment from a level higher 
than the appropriate value, an error results 
between the pressure gauge value and ac-
tually used pressure. (Due to Characteris-
tics of pressure-reduction valve 
respectively)

2 pressure-reduction valves provided on 
this machine allow you to connect MAX 

 and the general-purpose nailer or 

pneumatic tool.
<Pressure-reduction valve H>   Allows 
connection and use of MAX PowerLite 
tools (of operating pressure of 24.5 bars 
maximum)
<Pressure-reduction valve L>   Allows con-
nection and use of the general-purpose 
nailers or pneumatic tools (of operating 
pressure of 8.3 bars maximum)

AKHL1230E_UK.fm  17 ページ  2008年12月10日 水曜日 午後6時4分

Содержание powerlite AKHL1230E

























Отзывы: