Matthews VIAcode T100 Скачать руководство пользователя страница 32

Страница: 32 / 47

Maintenance – Ink-Bottle Replacement

T50/T100 PTM – User Guide – Version 2 Issue 1

Caution: Failure to mount the Nozzle-Protector-Plate

can lead to damage of the

PTM.

4. Turn the

Ink-Vent-Screw

fully clockwise. Do not overtighten it, use forefinger and thumb

force only.

Figure 23 - Preparing for moving, shipping, or storage

5. Unscrew and remove the

Ink-Bottle

from the

Ink-Inlet

6. Make sure that the

Ink-Inlet-Seal

, inside the

Ink-Inlet,

is correctly seated and then screw

Ink-Reservoir-Cap

in to the

Ink-Inlet

. Make sure that it is hand tight.

If storing or shipping the PTM continue from Step 7, otherwise the PTM is ready and no
further action is required.

7. Carefully put one plastic bag around the

Head

and one around the

Ink-Reservoir

. Use

elastic bands to seal and secure the plastic bags on to the PTM.

Note: The plastic bags will catch any ink spillage that may occur during transport.

8. Place the PTM inside its original packaging and seal it, so that it is securely protected

from being impacted or otherwise damaged.

The PTM is now ready for storage or shipping.

Ink-Bottle

Replacement

Caution

Use only Matthews approved inks. If any other ink type is used it may cause damage to
the PTM and void the warranty.

The

Ink-Bottle

should be replaced whenever the INK LED is lit

Orange

, indicating that the

ink level is low. To replace the bottle simply unscrew it, anti-clock-wise, and then replace it
with a new one.

The

Ink-Bottle

’s opening is fitted with a push valve which is pushed in whenever the bottle is

screwed in to the

Ink-Inlet

Ink-Vent-Screw

closed when
level with the
cover

Ink-Vent-Screw

Ink-Reservoir-Cap

Ink-Inlet-Seal

Содержание VIAcode T100
















































Результаты поиска

Содержание VIAcode T100

Отзывы:

Похожие инструкции для VIAcode T100

Бренды по названию

Популярные бренды

Matthews VIAcode T100, Руководство пользователя

Результаты поиска

Содержание VIAcode T100

Отзывы:

Похожие инструкции для VIAcode T100

Бренды по названию

Популярные бренды