Matsushima PFM-AP01 Скачать руководство пользователя страница 5

Страница: 5 / 18

5. Mounting

Please avoid mounting and using under the following circumstances not to be caused any short-life and
errors of devices.
-

Any place to be caused shaking, shocking and breakdown.

Any place of surround temperature out of rang 0

℃

to +50

℃

, surround humidity exceeding 80%RH and

under dew condensation.

Out door

5-1. Coverage of Wi-Fi communication

A guide of Wi-Fi communication distance is within approx. 100m a

pprox. 100m as direct distance in better

prospects without barricade.

# Please do mounting with confirming an available area for Wi-Fi communication. If any barricade

or stepping over rooms and floors, connection will be not available or to be unstable.

5-2. Mounting

Please do mounting Product using holes for mounting (M3 screw holes at 2 positions).
Please refer the recommended mounting directions on Fig. 2

Recommended mounting directions

Mounting directions not to be recommended

Please avoid the following mounting due to concerning low accuracy and deposition of
floating particles.

Fig. 2-2: Drawing of mounting directions not to be recommended

Down

Fig. 2-1: Drawing of recommended mounting directions

Содержание PFM-AP01



















Результаты поиска

Содержание PFM-AP01

Отзывы:

Похожие инструкции для PFM-AP01

Бренды по названию

Популярные бренды

Matsushima PFM-AP01, Руководство по эксплуатации

Результаты поиска

Содержание PFM-AP01

Отзывы:

Похожие инструкции для PFM-AP01

Бренды по названию

Популярные бренды