Matsusada AMPS Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 27

background image

16

4-10 Output Range

This amplifier is operatable in four-quadrant output range(unipolar type is operatable in

two-quadrant range), but when operated in DC mode or in low frequency operation please

derate the output as per the following diagram.

Rated output voltage
Rated output current

AC Operating range(frequency 50Hz and over/duty 50% and no DC bias)

DC Operation range

* For your safety be sure to earth the GND terminal

4 Instructions for operation

«
...
21
22
23
24
25
...
»

Содержание AMPS Series




























Отзывы:

Нет отзывов

Похожие инструкции для AMPS Series

Бренд: NAD Страницы: 16

Бренд: NAD Страницы: 2

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 4

Бренд: JBL Страницы: 44

Бренд: JBL Страницы: 23

Бренд: Ramsey Electronics Страницы: 20

Бренд: RAM Страницы: 16

Бренд: RAM Страницы: 4

Бренд: RAM Страницы: 46

Бренд: Xtant Страницы: 19

Бренд: Xtant Страницы: 2

Бренд: XINDAK Страницы: 12

ProX 840.4 COMP

Бренд: µ-Dimension Страницы: 12

Бренд: Luxman Страницы: 20

Бренд: Hill Audio Страницы: 12

Бренд: Trace Acoustic Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды