background image

8

Fit the flexible ducting into the Ducting

socket adaptor. 

Fit the unit into position. Tighten the

screws if necessary. Feed the flexible

ducting through the hole in the wall.

9

Fit the external grille.

10  The Charcoal filter is designed to remove

‘odours’ from dirty air. As the ‘odours’ are

being extracted to the outside air it is not

necessary to fit the Charcoal filter. 

11  Fit the main filter panel by locating the

rear pins in their slots and pressing the

release buttons. It will click into place.

12 Connect the Cooker Hood to the power

supply, as mentioned earlier in the guide.

Ducted air installation

1

The Cooker Hood must be fitted so that it

protrudes 160mm from the cupboard it is

being fitted to (see page 2). This is to

allow the re-circulated air to escape

through the grille in the top of the unit.

2  Use the card template supplied to mark

the position of the fixing screws. 

The keyhole slots are designed so the 

Cooker Hood locates over the larger area of

the hole and is then pushed back, onto the

smaller area of the hole. Two extra ‘security

screws’ are used to ensure the unit is secure and

isn’t accidentally pushed off the keyhole slots.

Screw the keyhole positioned screws into your

wall or kitchen cupboard so that the top

surface of the screw head is approximately

4mm from the surface you are screwing to. 

If you are top mounting the unit, drill all eight

holes, but don’t fit the four ‘security screws’

until the unit is in place.

3  Check that your fixings are correctly

located, by temporarily fitting the 

Cooker Hood. If correct, remove the

protective film from each side of the unit.

4  Fit the unit into position. Tighten the

screws if necessary.

5  Fit the Charcoal filter (not supplied –

please contact the store from which you

purchased your Cooker Hood) by first
lift the filter up into the Cooker Hood, 

aligning the posts with the locating holes 

on the filter. Turn the filter clockwise

to lock it into position.

6  Fit the main filter panel by locating the

rear pins in their slots and pressing the

release buttons. It will click into place.

7

Connect the Cooker Hood to the power

supply, as mentioned earlier in the guide.

Re-circulated air installation

6

Содержание MSH601BLK











Отзывы: