Matrox Meteor-II Скачать руководство пользователя страница 46

Страница: 46 / 70

Appendix B: Technical information

PC/104-Plus form
factor

Matrox Meteor-II for the PC/104

-Plus

form factor (stand alone version) has four

interface connectors: video input, a PC/104

-Plus

(PCI) connector, and two

PC/104 (ISA) connectors.

Note that the video input connector for the PC/104-

Plus

board built for

Matrox 4Sight-II is right-angled, unlike the one for the stand-alone version,
discussed here. See

Note about Matrox Meteor-II /Multi-Channel for PC/104-Plus

Chapter 2 for more details.

Video input connector on the PCI form factor

The video input connector is a high density DB-44 female connector on the PCI
form factor. Its pinout is as follows:

Pin

Signal

Description

VID1_IN1

RED Analog Video Input (Channel 1).

VID1_IN2

GREEN Analog Video Input (Channel 1).

VID1_IN3

BLUE Analog Video Input (Channel 1).

SYNC_IN

Analog Video Input (SYNC).

VID2_IN1

RED Analog Video Input (Channel 2).

PC/104-
(PCI)
connector

Plus

PC/104
(ISA)

and P2

connectors

Video input
connector

pin 1

pin 31

pin 16

pin 44

pin 15

pin 30

Содержание Meteor-II







































































Результаты поиска

Содержание Meteor-II

Отзывы:

Бренды по названию

Популярные бренды

Matrox Meteor-II, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание Meteor-II

Отзывы:

Бренды по названию

Популярные бренды