Matrox Meteor-II Скачать руководство пользователя страница 19

Страница: 19 / 70

Installing Matrox Meteor-II /Multi-Channel

2. Check that you have an available PC/104

-Plus

connector on the motherboard, or

verify that your existing stack can support another board.

3. Remove the anchoring screws from the stack; do not discard them since you will

need them to fasten the Matrox Meteor-II board.

4. If you have existing PC/104 boards in your computer, remove them and stack

them on the PC/104

-Plus

board. PC/104 boards must be stacked last.

5. Carefully position Matrox Meteor-II over the connectors and press the board

firmly into place.

6. Replace the anchoring screws.

7. Set the rotary switch (next to the PC/104 (ISA) P2 connector) to 0 if installing

the first stackable board, or another appropriate setting if not the first. See the
section,

Multiple board installation

, in Chapter 3.

8. Connect your video sources. For details, see the

Connecting external devices

section.

9. Turn on your computer.

Motherboard

PC/104-
(PCI) connector

Plus

PC/104
(ISA)
P1 and P2
connectors

Rotary
switch

Video input
connector

Содержание Meteor-II







































































Результаты поиска

Содержание Meteor-II

Отзывы:

Бренды по названию

Популярные бренды

Matrox Meteor-II, Руководство по установке и аппаратным средствам

Результаты поиска

Содержание Meteor-II

Отзывы:

Бренды по названию

Популярные бренды