Matrix MW401 Скачать руководство пользователя страница 9

9

Detergent

To fill the detergent compartment
1.  Push the latch as shown in figure 1.
2.  Add the required amount of detergent.  The main detergent  

 

 

compartment “b” (figure 2) has lines to allow for specific amounts of   

 

detergent.  These are marked at either 15 cm

3

 or 25 cm

3

, to be   

 

used depending on how dirty the dishes are.

 

If your dishes are in need of an intensive wash, then add 5 cm

3

 of   

 

detergent into the prewash section of the compartment “a” (figure 2).

3.  Then close the detergent compartment lid until the latch locks.

Please note: You should only use detergents designed specifically for 

use in dishwashers.

If using dishwasher tablets, always use the detergent compartment, do not put 

them in the main body of the dishwasher or in the cutlery basket.  The solubility 

of dishwasher tablets can vary depending on the temperature and duration of 

the programme.  As a result, it is recommended that powder detergents should 

be used in the shorter programmes to allow better performance.

CDA recommends the use of separate detergent, rinse aid and dishwasher salt 

rather than combination tablets as separates achieve better wash performance.

If you do use combination detergents, add salt and rinse aid to the dishwasher 

and then adjust the water hardness setting and rinse aid setting to the 

minimum.  When you then use separate detergents again, you should fill the 

salt and rinse aid compartments, adjust the water hardness setting to the 

maximum and run an empty wash, then adjust the water hardness setting and 

the rinse aid setting to the appropriate  level.

Salt

To ensure the best efficiency, the dishwasher needs soft water.  Hard water 

means that lime residues remain on the dishes and the interior of the 

dishwasher, affecting performance.  The softener system is designed to 

remove the ions that make the water hard to provide the best quality wash 

performance.  This is achieved by using dishwasher salt.

To add dishwasher salt, follow the steps below:
1.  Remove the lower dishwasher basket and then unscrew the salt   

 

compartment cap, as shown in figure 1.

2.  Fill the compartment with dishwasher salt (do not use table salt), carefully   

 

to prevent unnecessary spillage (figure 3).  Before first use, you should   

 

fill the compartment with 2kg of dishwasher salt and then fill up the salt   

 

compartment with water (up to the brim of the compartment) as shown   

 

in figure 3.

3.  Replace the cap and the lower basket.

When the salt warning light on the control panel illuminates, you should 

refill the salt compartment with salt only – do not add water to the salt 

compartment after the first use.

You should run a prewash programme immediately after adding 

dishwasher salt, to prevent any damage to the dishwasher systems.

fig 2

 

S A L T

 

fig 3

 

S A L T

 

 

fig 1

fig. 3

Detergent

To fill the detergent compartment
1.  Push the latch as shown in figure 1.
2.  Add the required amount of detergent.  The main detergent  

 

 

compartment “b” (figure 2) has lines to allow for specific amounts of   

 

detergent.  These are marked at either 15 cm

3

 or 25 cm

3

, to be   

 

used depending on how dirty the dishes are.

 

If your dishes are in need of an intensive wash, then add 5 cm

3

 of   

 

detergent into the prewash section of the compartment “a” (figure 2).

3.  Then close the detergent compartment lid until the latch locks.

Please note: You should only use detergents designed specifically for 

use in dishwashers.

If using dishwasher tablets, always use the detergent compartment, do not put 

them in the main body of the dishwasher or in the cutlery basket.  The solubility 

of dishwasher tablets can vary depending on the temperature and duration of 

the programme.  As a result, it is recommended that powder detergents should 

be used in the shorter programmes to allow better performance.

CDA recommends the use of separate detergent, rinse aid and dishwasher salt 

rather than combination tablets as separates achieve better wash performance.

If you do use combination detergents, add salt and rinse aid to the dishwasher 

and then adjust the water hardness setting and rinse aid setting to the 

minimum.  When you then use separate detergents again, you should fill the 

salt and rinse aid compartments, adjust the water hardness setting to the 

maximum and run an empty wash, then adjust the water hardness setting and 

the rinse aid setting to the appropriate  level.

Salt

To ensure the best efficiency, the dishwasher needs soft water.  Hard water 

means that lime residues remain on the dishes and the interior of the 

dishwasher, affecting performance.  The softener system is designed to 

remove the ions that make the water hard to provide the best quality wash 

performance.  This is achieved by using dishwasher salt.

To add dishwasher salt, follow the steps below:
1.  Remove the lower dishwasher basket and then unscrew the salt   

 

compartment cap, as shown in figure 1.

2.  Fill the compartment with dishwasher salt (do not use table salt), carefully   

 

to prevent unnecessary spillage (figure 3).  Before first use, you should   

 

fill the compartment with 2kg of dishwasher salt and then fill up the salt   

 

compartment with water (up to the brim of the compartment) as shown   

 

in figure 3.

3.  Replace the cap and the lower basket.

When the salt warning light on the control panel illuminates, you should 

refill the salt compartment with salt only – do not add water to the salt 

compartment after the first use.

You should run a prewash programme immediately after adding 

dishwasher salt, to prevent any damage to the dishwasher systems.

fig 2

 

S A L T

 

fig 3

 

S A L T

 

 

fig 1

fig. 4

If you do use combination detergents, add salt and rinse aid to the 
dishwasher and then adjust the water hardness setting and rinse aid setting 
to the minimum. When you then use separate detergents again, you should 
fill the salt and rinse aid compartments, adjust the water hardness setting 
to the maximum and run an empty wash, then adjust the water hardness 
setting and the rinse aid setting to the appropriate level.

Salt

To ensure the best efficiency, the dishwasher needs soft water. Hard water 
means that lime residues remain on the dishes and the interior of the 
dishwasher, affecting performance. The softener system is designed to 
remove the ions that make the water hard to provide the best quality wash 
performance. This is achieved by using dishwasher salt.

To add dishwasher salt, follow the 
steps below:
1.   Remove the lower dishwasher basket 

and then unscrew the salt compartment 
cap, as shown in figure 3.

2.   Fill the compartment with dishwasher 

salt (do not use table salt), carefully 
to prevent unnecessary spillage 
(figure 4). Before first use, you should 
fill the compartment with 2kg of 
dishwasher salt and then fill up the salt 
compartment with water (up to the 
brim of the compartment) as shown in 
figure 4. 

Содержание MW401





























Отзывы: