manualshive.com logo in svg

Mathias Bauerle Multipli 35, Руководство оператора

Поделиться
Скачать
Mathias Bauerle Multipli 35 Скачать руководство пользователя страница 63

The photodetector of the double sheet control recognizes when more than one sheet
is fed from the stack at the same time.
If this is the case, paper transport is stopped.
The double sheet detection covers paper weights (offset quality) from 40 to 170 GSM.

Operator's Manual

multipli 35

Double Sheet Detection

68

Mathias Bäuerle GmbH

20. DOUBLE SHEET DETECTION

I

I

0

0

1

2

3

4 5

6

8

7

Description

1 On/Off switch

double sheet detection

2 Knob

for adjusting the double sheet detection

3 LED, red

setting aid

4 LED, yellow

setting aid

5 LED, green

indicates ready state

6 LED, red

indicates double sheets

7 Reset button

clears double sheet indication

8 On/Off switch

Operator panel

Setting

•

Switch on the operator panel (8).

•

Turn on the double sheet detection with
switch (1). The green LED (5) indicates
that it is ready for operation.

•

Slide a folded sample sheet (an unprinted
section) under the photodetector (9).

•

Slowly turn the knob (2) to the left or to the right until:
1. the green LED goes out
2. the two red LEDs come on
3. the yellow LED just comes on and is barely visible

•

Remove the double sample sheet.
LED display:

green LED is on
red LED is on

•

Press key C.
LED display:

red LED goes out
green LED is on

9

If the double sheet detection is adjusted several times, the sample sheet
must not stay under the photodetector. It must be placed anew under the
photodetector every time an adjustment is made.

www.WhitakerBrothers.com

Содержание Multipli 35




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды