Matco Tools MUC122R Скачать руководство пользователя страница 6

MUC122R 

rev. 09/10/13

MUC122R 12V Ratchet

SAVE THESE INSTRUCTIONS!

SAFETY INSTRUCTIONS FOR BATTERY 

CHARGER AND BATTERY PACK

DANGER! READ CAREFULLY
120 Volts present at charging terminal. Absolutely DO NOT 
probe with conductive objects.

1 .   CAREFULLY READ AND UNDERSTAND THESE  

 

 INSTRUCTIONS 
 

This manual contains critical safety and operating 

 

instructions for the tool, battery charger, and battery .

2 .   Before using battery charger, read all instructions and   
 

cautionary markings on (1) battery charger, (2) battery,  

 

and (3) product using battery .

3 .   CAUTION - To reduce risk of injury, charge only MATCO 
 

rechargeable batteries marked on the charger label .  

 

Other types of batteries may burst causing personal  

 

injury and damage .

4 .   Do not expose charger to rain or snow .
5 .   Use of an attachment not recommended or sold by Matco  
 

or the battery charger manufacturer may result in a risk of  

 

fire, electric shock, or injury to persons .

6 .   To reduce risk of damage to electric plug and cord, pull by  
 

plug rather than cord when disconnecting charger .

7 .   Make sure cord is located so that it will not be stepped on,  
 

tripped over, or otherwise subjected to damage or stress .

8 .   An extension cord should not be used unless absolutely 
 

necessary . Use of improper extension cord could result in 

 

a risk of fire and electric shock . If extension cord must be 

 

used, make sure:

 

a .   That pins on plug of extension cord are the same   

 

    number size, and shape as those of plug on charger;

 

b .   That extension cord is properly wired and in good   

 

    electrical condition;

 

c .   That wire size is at least as large as the one specified  

 

    in the table below .

 

Table 1: RECOMMENDED MINIMUM AWG SIZE FOR    

 

EXTENSION CORDS FOR BATTERY CHARGERS

Length of Cord (Feet)  

25   50   75   100  150

AWG Size of Cord  

18   18   16   14    12

9 .   Do not operate charger with damaged cord or plug -    
 

replace them immediately .

10 .  Do not operate charger if it has received a sharp blow,  
 

been dropped, or otherwise damaged in any way;  

 

take it to a MATCO AUTHORIZED service facility .

11 .  Do not disassemble charger or battery cartridge; 
 

take it to your MATCO AUTHORIZED distributor service   

 

facility .  Incorrect reassembly may result in a risk  

 

of electric shock or fire .

12 .  To reduce risk of electric shock, unplug charger from   
 

outlet before attempting any maintenance or cleaning .  

 

Turning off controls will not reduce this risk .

13 .  The battery charger is not intended for use by young    
 

children or infirm persons without supervision .

14 .  Young children should be supervised to ensure that they  
 

do not play with the battery charger .

OPERATIONAL GUIDELINES  

FOR BATTERY CHARGER AND 

BATTERY PACK

1 .   Do not attempt to use a step-up transformer, an engine  
 

generator or DC power receptacle .

2 .   Do not allow anything to cover or clog the charger vents .
3 .   Always cover the battery terminals with the box or cover  
 

when the battery cartridge is not used .

4 .   Do not short the battery cartridge:
 

(1)  Do not touch the terminals with any conductive    

     material .
 

(2)  Avoid storing battery cartridge in a container  

 

    with other metal objects such as nails, screws,  

 

    coins, etc .

 

(3)  Do not expose battery cartridge to water 

 

    or rain . A battery short can cause a large current flow,  

 

    overheating, possible burns and even a breakdown .

5 .   Do not store the tool and Battery Cartridge in locations  
 

where the temperature may reach or exceed  

 

50°C (122°F) .

6 .   Do not incinerate the Battery Pack even if it is  
 

severely damaged or is completely worn out .  

 

The battery cartridge can explode in a fire .

7 .   Be careful not to drop, shake or strike battery  
 

as it will affect the capacity and may void warranty .

8 .   Do not charge inside a box or container of any kind .  
 

The charger and battery are ventilated devices and 

 

must NOT be placed next to a heat source or in 

 

exposure to radiating heat . 

9 .  Place charger on a solid and sturdy surface as there are  
 

vents on the bottom side of the charger .

10 .  Always unplug the charger from the power supply when a  
 

charging sequence is not taking place . 

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.

WARNING

Содержание MUC122R






















Отзывы: