MasterForce 241-0781, Руководство по эксплуатации

Страница: 4 / 8

6 7
SERVICE
Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result
in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instructions may
create a risk of electric shock or injury.
SPECIFIC SAFETY RULES FOR ANGLE GRINDER
Always use the proper guard with the grinding wheel.
A guard
protects operator from broken wheel fragments. When using grinding
wheel attachments, the guard must always be attached to the tool and
positioned for maximum safety, so the least amount of wheel is exposed
from the side from which the tool is being operated.
Accessories must be rated for at least the speed recommended on the
tool warning label.
Wheels and other accessories running over the
rated speed can fly apart and cause injury. Grinding wheels or any other
accessory must have a maximum safe operating speed greater than the
“no load RPM” marked on the tool’s nameplate.
Hold the tool by its insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own
cord. Contact with a “live” wire will make exposed metal parts of the tool
“live” and shock the operator.
Always use the auxiliary handle for maximum control over torque
reaction or kick-back. Operation of the grinder without the side handle
could cause loss of control of the grinder, resulting in possible serious
personal injury.
Before using a grinder or installing a new wheel, inspect the grinding
wheel for chips and cracks. Remove bad wheels immediately. Run the
tool at no load for one minute, holding the tool in the direction away from
people. Wheels with flaws will normally break apart during this time.
Carefully handle both the tool and individual grinding wheels to avoid
chipping or cracking. Install a new wheel if the tool is dropped while
grinding. Do not use a wheel that may be damaged. Fragments from a
wheel that bursts during operation will fly away at great velocity, possibly
striking you or bystanders.
Do not use a grinding wheel that is larger than the maximum
recommended size for your tool or worn down damaged wheels from
larger grinders.
Wheels intended for large angle sander/grinders are not
suitable for the high speed of a small angle sander/grinder; these wheels
may easily burst and the fragments strike you or bystanders.
Do not use depressed hub grinding wheels for cut-off operations.
Depressed hub wheels or type 27 wheels are not intended for side loading
and may shatter under overload.
Do not use this tool with a “Woodcarving” blade.
Such blades create
frequent kick-back and loss of control.
Wear proper apparel while using a sander/grinder. Wear a face shield
(or at least safety goggles), dust mask, leather gloves and shop apron
capable of stopping small wheel or workpiece fragments.
Position the cord clear of the spinning grinding wheel or any other
sanding accessory. Do not wrap the cord around your arm or wrist.
If you
lose control and have the cord wrapped around your arm or wrist it may
entrap you and cause injury.
Avoid bouncing and snagging the wheel, especially when working
corners, sharp edges, etc. This can cause loss of control and kick-back.
Regularly clean the tool’s air vents by compressed air. Excessive
accumulation of powdered metal inside the motor housing may cause
electrical failures.
Do not grind or sand near flammable materials. Sparks from the wheel
could ignite these materials.
This tool can be converted to a sander. When grinding is resumed the
proper guard and wheel flanges must be reinstalled before proceeding
with grinding. The guard must always be attached to the tool and
positioned for maximum safety, so the least amount of wheel is exposed
from the side the tool is being operated. The grinding wheel guard cannot
be used for most sanding operations or for wire brushing.
When sanding, do not use an oversized sanding disc. A larger sanding
disc will extend beyond the sanding pad,causing snagging, tearing of the
disc or kick-back. Extra paper extending beyond the sanding pad can also
cause serious lacerations.
When sanding chemically pressure-treated lumber, paint that may be
lead based, or any other materials that may contain carcinogens, use