Safety
3
DESCRIPTION
This Pedestal Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-
type power cord. Sleeve bearings on motor shaft never
need lubrication. Automatic reset thermal protection.
Pump water only with this pump.
NOTICE:
This unit is not designed as a waterfall, pond,
or fountain pump, or for applications involving salt
water or brine! Use with waterfalls, ponds, fountains,
salt water or brine will void warranty.
Do not use where water recirculates.
Not designed for use as a swimming pool drainer.
SPECIFICATIONS
Power supply required ........................115V, 60 HZ.
Horsepower ........................................................1/3
Motor duty .............................................Intermittent
Liquid Temp. Range ...............32°F to 70°F(0°-21°C)
Individual Branch Circuit
Required GFCI Class A...............................15 Amps
Motor full load (maximum) .......................3.5 Amps
Discharge:.............................................1-1/2" FNPT
PERFORMANCE
GENERAL SAFETY
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump’s capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from
functioning normally. To prevent possible water
damage due to flooding, consult your retailer about
a secondary AC sump pump, a DC backup sump
pump, and/or a high water alarm. See the
“Troubleshooting Chart” in this manual for
information about common sump pump problems
and remedies. For more information, call customer
service at 1-877-455-5508.
1.
Know the pump application, limitations, and
potential hazards.
Do not use in explosive
atmospheres. Pump water
only with this pump. Failure to follow this warn-
ing can result in personal injury and/or property
damage.
2.
Disconnect power before servicing.
3.
Release all pressure within system before ser-
vicing any component.
4.
Drain all water from system before servicing.
Risk of flooding. If a flexible
discharge hose is used, pump
may move when motor starts.
If it moves far
enough so that switch hits side of sump, switch
may stick and prevent pump from starting.Make
sure pump is secured so it cannot move around
in sump.
5.
Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property dam-
age.
6.
Check hoses for weak or worn condition before
each use, making certain all connections are
secure.
7.
Inspect sump, pump and system components
monthly. Keep free of debris and foreign
objects. Perform routine maintenance as
required.
FIRE HAZARD - Do not store
or rest objects on or near
motor or switch linkage. Keep all flammable
objects or liquids away from motor.
8.
Provide means of pressure relief for pumps
whose discharge line can be shut-off or
obstructed.
9.
Personal Safety:
a. Wear safety glasses at all times when work-
ing with pumps.
b. Keep work area clean, uncluttered and prop-
erly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
keys.
10. When wiring an electrically driven pump, fol-
low all electrical and safety codes, as well as
most recent National Electrical Code (NEC) and
Occupational Safety and Health Act (OSHA).
11. This equipment is only for use on 115 volt
(single phase) and is equipped with an
approved 3-conductor cord and 3-prong,
grounding-type plug.
To reduce risk of electric
shock, be certain that it is
connected to properly grounded, grounding-
type receptacle.
Never connect green (or
green and yellow) wire in
cord to a live terminal!
Where a 2-prong wall receptacle is encoun-
tered, it must be replaced with properly
grounded 3-prong receptacle installed in accor-
dance with the National Electrical Code and
local codes and ordinances.
12. All wiring should be performed by a qualified
electrician.
13. Make certain that power source conforms to
requirements of your equipment.
14. Protect electrical cord from sharp objects, hot
surfaces, oil, and chemicals. Avoid kinking
cord. Replace or repair damaged or worn cords
immediately.
15. Do not touch an operating motor. Modern
motors can operate at high temperatures. Keep
the motor dry at all times.
16. Do not handle pump or pump motor with wet
hands or when standing on wet or damp sur-
face, or in water.
GPH (LPH) AT TOTAL FEET (M)
5 Ft.
10 Ft.
15 Ft.
20 Ft.
(1.52)
(3.05)
(4.57)
(6.09)
3000
2460
1620
0
(11 355L)
(9 312L)
(6 131L)
(0L)