MasterCraft 062-3415-8 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 15

MasterCraft 062-3415-8 Скачать руководство пользователя страница 6

model no. 062-3415-8 | contact us 1-800-689-9928

SAFETY

ADDITIONAL SAFETY PRECAUTIONS

1. Know the pump applications, limitations, and potential hazards.

2.  Make certain the electrical power source is adequate for the requirements of the pump.
3.  ALWAYS disconnect the power to the pump before servicing.
4.  Release all pressure within the system before servicing any component (drain all water from

the system).

5. Secure the discharge line before starting the pump. An unsecured discharge line could whip,

possibly causing personal injury and/or property damage.

6. Secure the pump on a solid base.

7. Check that all pipe connections are tight to minimize leaks.
8. Make certain the electrical circuit to the pump is protected by a dedicated 15 A or larger fuse

or circuit breaker.

9. Never use extension cords with this pump!

10. Do not handle pump or pump motor with wet hands or when standing on a wet or damp

surface, or in water.

11. Wear safety glasses at all times when working with pumps.
12. Follow all electrical and safety codes, particularly the National Electrical Code (NEC) or the

Canadian Electrical Code (CEC), and in the workplace, the Occupational Safety and Health Act
(OSHA) or the Canadian Centre for Occupational Health and Safety (CCOHS).

13. This unit is designed only for use on 115 V or 230 V, 60 Hz. Directly connect pump wires into

properly grounded circuit board in accordance with the NEC or CEC and local codes and
ordinances. All wiring should be performed by a qualiﬁed electrician.

14. Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking

the cord. Do not use damaged or worn cords. Failure to properly wire this pump is dangerous
and will void the warranty.

6

«
...
4
5
6
7
8
...
»

Содержание 062-3415-8
















Отзывы:

Нет отзывов