manualshive.com logo in svg

MasterCraft 062-3415-8, Инструкция по эксплуатации, Страница: 11 / 15

Поделиться
Скачать
MasterCraft 062-3415-8 Скачать руководство пользователя страница 11

INSTALLATION INSTRUCTIONS

10

12

This pump is pre-wired at 115 V. If the power 

source is 230 V, remove the electrical 

housing cover. Flip the switch to 230 V. 

Replace the cover.

NOTE: All electrical work should be 

performed by a licensed electrician.

11

To prime, remove both: 

a. The plug from the top of the discharge 

tee (fill pump and piping through 

priming tee); and 

b. The priming plug in front of the 

discharge tee (this is to allow air to 

vent out while priming).

Fill the discharge tee with water until 

water overflows.

NOTE: It may take several minutes or 

more to fill the pipes and the pump (A) 

completely. Watch the water level in the 

discharge tee. Make sure the water level 

is stable and there are no air bubbles.

WARNING: If the pump is lower than the 

suction pipe, air may get trapped in the 

pipe. The pump may not work properly. 

Make sure the pipe slopes away from the 

pump.

Wrap the discharge tee plug and priming 

plug threads with thread tape and 

re-attach to the pump (A). Tighten with a 

wrench.

Air pressure in the tank must be 2 PSI lower than the "cut-in" of the pressure switch.

NOTE: The pump (A) has a 30/50 PSI pressure switch, which means the "cut-in" is 30 PSI; 

therefore, the tank needs to be set to 28 PSI. To check the pressure in the tank, use a tire 

pressure gauge. If more air is needed, add air to the tank with a tire pump or air compressor. 

If less is needed, bleed out some air.

11

115

230

Содержание 062-3415-8
















Отзывы:

Нет отзывов