manualshive.com logo in svg

MasterCraft 062-3408-6, Инструкция по эксплуатации, Страница: 4 / 20

Поделиться
Скачать
MasterCraft 062-3408-6 Скачать руководство пользователя страница 4

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

model no. 062-3408-6 | contact us 1-800-689-9928

4

QUICK ST

AR

T GUIDE

PLUGGING IN THE PUMP

Place the pump on a solid base in a 
flooded area or any place that you
would like to remove water. Plug the 
pump into a 115 V GFCI power
outlet.

2

OPERATING THE PUMP

Allow the pump to run and monitor its 
progress.
Unplug the pump when it has removed 
water down to approximately 1/2" 
(12.7 mm).

3

CONNECTING GARDEN HOSE 

Attach a garden hose with a 3/4" (19 mm) 
garden hose thread (not included) to
the pump outlet. 

1

1/2” (12.7 mm)

Anti-airlock

hole

1 1/2” (38.1 mm)

NOTE:

•   Be sure the 3/4" (19 mm) garden hose thread connector has a rubber gasket to minimize water leaks.

•   The larger the inside diameter and the shorter the length of hose, the less pressure that is lost (or the larger the 

flow rate).

•   Place upright on a solid base. 

•   The pump must be standing in at least 1 1/2" (38.1 mm) of water before you start it. The shaft seal is water 

lubricated and may be damaged if the pump runs dry.

3/4" (19 mm) NH

thread

Submersible Utility Pump Function

CAUTION!

•   Do not allow the plug to fall in water and do not stand in water while the pump is plugged in.
•   Do not run the pump dry. Operating the pump without water will cause damage to the seals and will cause the pump to 

fail, thereby voiding the pump’s warranty.

•   The anti-airlock hole is for anti-airlock purposes only. Leakage of air or water is normal and necessary. DO NOT 

REMOVE OR PLUG THE ANTI-AIRLOCK HOLE!

Содержание 062-3408-6





















Отзывы:

Нет отзывов