manualshive.com logo in svg

MasterCraft 062-3408-6, Инструкция по эксплуатации, Страница: 15 / 20

Поделиться
Скачать
MasterCraft 062-3408-6 Скачать руководство пользователя страница 15

headline bars

continuation tabs

notes

warnings

15

ASSEMBL

Y INSTRUCTIONS

• 

Attach the clear suction hose to the suction 
strainer. 

• 

Then, place the strainer in at least 1" (2.5 cm) of 
water at the lowest point to be pumped.

The following picture shows a typical installation. The suction lift of this unit can get up to 8' (2.4 m). 
Be sure to use the included, specially designed built-in check valve suction strainer. 

NON-SUBMERSIBLE TRANSFER PUMP INSTALLATION

CAUTION!

•    Always use the handle to lift the pump. Never use the power cord to lift the pump. To avoid skin burns, unplug the 

pump and allow time for it to cool after periods of extended use.

WARNING!

•    Always disconnect power source before attempting to install, service, or maintain the pump. Never handle a pump 

with wet hands or when standing on wet or damp surface or in water. Fatal electrical shock could occur.

•    Do not handle the pump or pump motor with wet hands or when standing on a wet or damp surface or in water 

while the pump is plugged in. 

NOTE:

• Make sure the connection is airtight. An air leak can cause the pump to run dry.

• Always ensure the washer in the hose bib is not damaged. An airtight seal is necessary for this pump to operate.

Priming plug

Suction hose 

Suction strainer

1" (2.5 cm) 

Содержание 062-3408-6





















Отзывы:

Нет отзывов