MasterCraft 054-8363-0 Скачать руководство пользователя страница 14

Страница: 14 / 17

headline bars

continuation tabs

notes

warnings

model no. 054-8363-0 | contact us 1.800.689.9928

TROUbLeSHOOTINg

Problem

Possible Causes

Solution

The motor does not start

The tool is not connected to a power
source

Connect the tool to a power
source

The blade does not follow a
straight line

1. Teeth are dull. This is caused by hitting

a hard object such as a nail, dulling
teeth on one side. The blade tends to
cut to the side with the sharpest teeth.

1. Replace with a new sharp

blade

2. Edge guide or straight edge is not

being used.

2. Use an edge guide or

straight edge

The blade binds or smokes
from friction

1. Blade is dull.

1. Replace with a new sharp

blade

2. Blade is on backwards.

2. Install the blade correctly

3. Blade is bent.

3. Replace with a new blade

4. Workpiece is not properly supported.

4. Clamp the workpiece

correctly and tightly

5. Incorrect blade is being used.

5. Use the correct blade

If any parts are missing or damaged, or if you have any questions, please call the Toll-free Helpline,
at 1-800-689-9928.

exPLOded VIew

TROUBLESHOO

TING

PAR

T LIST

Содержание 054-8363-0


















Результаты поиска

Содержание 054-8363-0

Отзывы:

Бренды по названию

Популярные бренды

MasterCraft 054-8363-0, Инструкция по эксплуатации

Результаты поиска

Содержание 054-8363-0

Отзывы:

Бренды по названию

Популярные бренды