background image

9

103618

OWNER’S MANUAL

Spark Plug

(35,000 Btu/Hr Model)

1.

Remove upper shell (see page 8).

2.

Remove fan (see page 13).

3.

Remove fuel and air line hoses from
nozzle assembly.

4.

Remove spark plug wire from spark plug.

5.

Remove two screws using 5/16" nut-
driver and remove burner strap.

6.

Place hex-body of spark plug into vise
and tighten.

7.

Remove spark plug mounting nut us-
ing 11/16" open-end wrench.

8.

Remove burner strap from spark plug.

9.

Clean and regap spark plug electrodes
to 1.4 mm (.055") gap.

10. Replace burner strap onto spark plug.

Rotate burner strap to position spark
plug electrodes (see Figure 13).

11. Tighten spark plug with spark plug

mounting nut.

12. Release hex-body of spark plug from

vise.

13. Replace burner strap onto combustion

chamber.

14. Attach spark plug wire to spark plug.

15. Attach fuel and air line hoses to nozzle

assembly.

16. Replace fan (see page 13).

17. Replace fan guard and upper shell.

Figure 13 - Spark Plug Rotation, 35,000
Btu/Hr Model Only

Figure 12 - Spark Plug Gap, 35,000 Btu/Hr
Model

Figure 11 - Spark Plug Removal, 35,000
Btu/Hr Model

SERVICE
PROCEDURES

Continued

Continued

Combustion
Chamber

Burner Strap

Nozzle
Assembly

Fuel Line
Hose

Air Line
Hose

Spark Plug
Mounting Nut

Spark Plug

Spark
Plug
Wire

Bend Here
to Adjust
Gap

1.4 mm
(.055")
Gap

Burner
Strap

Burner
Strap

Spark Plug

(70/100/150,000 Btu/Hr Models)

1.

Remove upper shell (see page 8).

2.

Remove fan (see page 13).

3.

Remove spark plug wire from spark plug.

4.

Remove spark plug from burner head
using 13/16" open-end wrench.

5.

Clean and regap spark plug electrodes
as follows:

70/100,000 Btu/Hr Models:

1.9 mm (.075") gap

150,000 Btu/Hr Model:

2.8 mm (0.110") gap

6.

Install spark plug in burner head.

7.

Attach spark plug wire to spark plug.

8.

Replace fan (see page 13).

9.

Replace fan guard and upper shell.

Figure 14 - Spark Plug Removal, 70/100/
150,000 Btu/Hr Models

Burner
Head

Spark
Plug
Wire

Spark
Plug

Figure 15 - Spark Plug Gap, 70/100/150,000
Btu/Hr Models

Bend Here
to Adjust
Gap

Gap

Содержание BY100CEB

























Отзывы: