Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals).
It is in any case advisable to carry out a technical inspection prior to installing any radio system in order to identify possible
sources of interference.Radio systems can be used where any disturbances or malfunction of the transmitter or receiver
do not constitute a risk factor, or if such factor is eliminated using appropriate safety systems.The presence of radio
devices working at the same transmission frequency (433.42 MHz) may interfere with the radio receiver and reduce the
range of the system, limiting functionality.
R
www.mastermotion.eu
433,42 MHz
User manual:
ARCO
ARCO 2
ARCO 5
ARCO 10
ARCO 20
rev03_22.06.17
ARCO5 - ARCO10 - ARCO20
Dear Customer, thank you for purchasing a MASTER
S.p.A. product. This guide contains all the information you
will need concerning the use of this product. Read the
instructions carefully and keep them for further
consultation.
ARCO is designed specifically to control sun awnings,
blinds, roller shutters, screens or similar items. All other
use beyond the field defined by MASTER S.p.A. is
forbidden. This, as well as the breach of the instructions
given in this guide, shall release MASTER S.p.A. from any
liability and shall annul the product warranty. Water,
humidity, heat sources, accidental falls can damage the
device. Do not use abrasive products or solvents to clean
the product.
Package contents
- 1 transmitter
- 1 CR2032 lithium battery
- 1 wall bracket
- 2 dowels
- 1 this manual
Technical specifications
- Power supply:
n° 1 CR2032 lithium battery
- Operating temperature:
0° C / +55°C
- Operating frequency:
433.42 Mhz
- Operating frequency band: 433,050 – 434,790 Mhz
- Max radiated power, e.r.p. :
<10 mW
- N° of channel ARCO:
1
- N° of channels ARCO2:
2 + sequencer channel
- N° of channels ARCO5:
5 + sequencer channel
- N° of channels ARCO10: 10 + sequencer channel
- N° of channels ARCO20: 20 + 4 groups
Notes on radio systems
At the end of the product life cycle, dispose of the device in compliance with local
regulations. This product could contain substances that are harmful to human health and
the environment: do not dispose of the product in domestic waste.
Battery insertion/replacement
The transmitter is powered by a battery C R2032. To insert the
battery, remove the battery cover on the back of the
transmitter, insert the battery respecting the polarity, close the
cover.
Use of batteries different than those referred can
cause an explosion hazard. Used batteries must be
discarded in appropriate containers.
It it recommended to
replace the battery every 2 years.
Fixing the wall bracket
A) Fix the bracket to the wall using the supplied plugs (distance between holes 36 mm).
B) Cover the screw heads with the coverage provided.
C) Hang the transmitter to the support.
Disposal
1. FUNCTIONS ASSOCIATED WITH THE TRANSMITTER BUTTONS
Basic functions
up
stop
down
channel -/+
prev/next
SUN On/Off
FOR ME
right orientation
left orientation
To memorize:
To recall:
access to the
receiver menu
transmitters
insertion-deletion
MENU
PROG
Favorite position
Sun/automatic lowering function
2. ENABLING/DISABLING GROUPS AND CHANNELS
NOTE:
In ARCO2 the «
Sun/Automatic lowering»
function is active for
both
channels: if you enable it for channel 1, it is automatically activated for channel 2 and viceversa It is possible
that some receiving devices do not associate any operations to some transmitter buttons or that associate to the transmitter buttons some operations different from what it is described. In
this case consider the instruction manual of the receiving device.
3. DELAY OF TRANSMISSION ON GROUPS AND SEQUENCER CHANNEL
ARCO 2, ARCO 5 and ARCO 10
transmitters have a virtual channel called
Sequencer
, which sends the selected command in succession for all active radio channels. To select the
Sequencer
, scroll the list of channels until
SE
symbol appears. The
ARCO 20
transmitter is equipped with 4 virtual channels (called
Groups
, indicated with
G1
,
G2
,
G3
,
G4
) which send the
selected command in succession for all the active radio channels belonging to the group. To select a group, scroll the list of channels until the symbols G1, G2, G3 and G4 appear.
It is possible to set the interval (from 1 to 10 sec) of time which must pass between the transmission on one channel and the next. The factory sets the delay at 1 second. The use of high
intervals of time can negatively effect on the battery life.
To modify the setting:
4. SETTING THE CHANNELS BELONGING TO A GROUP (only ARCO20)
The
ARCO 20
transmitter is equipped with 4 virtual channels (Groups, indicated by
G1
,
G2
,
G3
,
G4
) which send the selected command in succession for all the active radio channels
belonging to the group. It is possible to associate up to 20 channels to each group.
To set different groups, follow the procedure:
C) If
YELLOW LED IS ON
: sun/automatic lowering function
active
B) Press until the state of the yellow LED varies (about 2seconds)
A) Select the channel (excluded sequencer channel and groups)
All products and technical specifications given in this document are
subject to variation without notice. Unless previously and
specifically authorised by the manufacturer, the device must be
used exclusively with receivers produced by the same
manufacturer. The manufacturer shall not be liable for damage
resulting from improper, incorrect or unreasonable use.
Press STOP and then FOR ME and hold
the buttons until the motor signalation (about 5 seconds)
MENU
PROG
A)
Press
STOP and then MENU
and hold the buttons for about 3 seconds, until the
ch
symbol is displayed.
B)
Press
STOP
.
01
will appear.
C)
If
YELLOW LED IS ON
:
channel/group enabled
/ If
RED LED IS ON
:
channel/group enabled
D)
Press
STOP
to modify the setting.
E)
If necessary,press PREV and NEXT to select another channel/group and return to point C.
F)
To exit,
press twice MENU
or wait about 15 seconds (the display switches off).
A)
Press
STOP and then MENU
and hold the buttons for about 3 seconds, until the
ch
symbol is displayed.
B)
Press
NEXT
. The
Sd
symbol appears on the display.
C)
Press
STOP
. The currently set value appears on the display (from 01 to 10 sec).
D)
Use
PREV
and
NEXT
to set the required value.
E)
Press
STOP
to save the setting.
F)
To exit,
press 1 time MENU
or wait about 15 seconds (the display switches off).
A)
Press
STOP and then MENU
and hold the buttons for about 3 seconds, until the
ch
symbol is displayed.
B)
Press twice NEXT.
G1
symbol appears on the display. To select another group press NEXT.
C)
Press STOP. Channel 01 appears.
D)
If
YELLOW LED IS ON: channel belongs to the group
/ If
RED LED IS ON
:
channel not belongs to the group
E)
Press
STOP
to modify the setting.
F)
If necessary, press PREV and NEXT to select another channel and return to point E.
G)
To exit,
press twice MENU
or wait about 15 seconds (the display switches off).
With transmitters ARCO 5, ARCO 10 and ARCO 20 you can turn off the channels that are not used; this will facilitate the use of the transmitter because when you scroll through the list of
channels, you find only those actually used. It's possible, with the same procedure, reactivate the channels.
The procedure is as follows:
By the «SUN On / Off " button you can activate / deactivate the SUN function or the AUTOMATIC LOWERING function, in the receivers equipped with these functions. To modify the setting:
