background image

TROUBLESHOOTING 

 

 
 
 

 

Pump Will Not Turn On 

Check For Loose Wiring 
Make Sure Switch Is Turned On 
Check The Fuse 
Check For Defective Pressure Switch 
Tap On Motor To Ensure Brushes Not Stuck 

Low Pressure/Low Flow 

Check If Inlet Hose/Filter To Pump Is Clogged 
Check For Proper Battery Voltage To Pump 
Flush Pump w/ Garden Hose  Up To Strainer 

Pump Cycles 

Adjust Spray Wand Tip To See If There Is Back Pressure From 
Too Fine of a Mist 
Boom Nozzle/Filter Clogged 
Check If Filter In Handle Is Clogged 

Fuse Is Blown 

Excess Voltage 
Damaged or Defective Wiring Harness 
Defective Pump Motor 
Pump Continually Cycles On/Off Creating Too Much Amp 
Draw 

Pump Leaks 

Check For Loose Fasteners & Tighten 
Check Pump Seals Degraded. Replace If Needed 
Leak In Diaphragm. Replace Diaphragm Assembly 

Poor Spray Distribution 

Check Suction Strainer & Clean If Necessary 
Clogged Intake Tube. Clean If Needed 
Worn Spray Gun Nozzle. Replace Spray Gun 

Pump Cycles While 
Spraying 

Check For Leak In System. Tighten Clamps, Fittings or Replace 
Spray Gun 
Pressure Switch Might Be Faulty. Replace 
Check Voltage To Determine If Low 
Air Might Be Trapped In System, Purge Air 

 

 
 
 
 
 

 

Содержание S3O-61-060D-MM















Отзывы: