background image

Binks Model 7

 Spray Gun

(6100-XXXX-X)

Replaces 

Part Sheet 

77-1153R-22

Part 

Sheet

77-1153R-23

Your new Binks spray gun is exceptionally 
rugged in construction, and is built to stand 
up under hard, continuous use. However, like 
any other fine precision instrument, its most 
efficient operation depends on a knowl edge 
of its construction, operation, and mainte-
nance. Properly handled and cared for, it will 
produce beautiful, uniform finishing results 
long after other spray guns have worn out.

TyPeS of InSTallaTIon

SIPHon feeD CUP HooKUP

Air pressure for atomization is regulated at 
extractor. The amount of fluid is adjusted by 
fluid control screw on gun, viscosity of 
paint, and air pressure (see figure 1).

Clean air™ 

filter

figure 1

air

Siphon Cup

Clean air™ 

filter

Cup 

Regulator

figure 2

air

fluid Pressure 

Cup

Clean air™ 

filter

figure 5

air

fluid

fluid 

Regulator

fluid

figure 4

air 

Supply

air Supply

Pressure 

Tank

Clean air™ 

filter

air 

Inlet

figure 3

air

Pressure 

Tank

fluid

PReSSURe feeD TanK HooKUP

For portable painting operations 
(double regulator).
Air pressure for atomization and fluid sup-
ply is regulated by two individual air regu-
lators on tank (see figure 4).

PReSSURe feeD CIRCUlaTInG 

HooKUP

For heavy production spraying.
Air pressure atomization regulated at 
extractor. Fluid pressure regulated at fluid 
regulator (see figure 5).

PReSSURe feeD TanK HooKUP

For medium production spraying   
(sin gle  regulator).
Air pressure for atomi zation is regulated at 
extractor, fluid pressure at tank regulator 
(see figure 3).

PReSSURe feeD CUP HooKUP

For fine finishing with limited spraying.
Air pressure for atomization is regulated at 
extractor; fluid pressure at cup regulator. 
For heavy fluids and internal mix nozzle 
spraying, fluid adjusted by control screw 
on gun.
Pressure cup also available less regulator 
(see figure 2).

Содержание 7









Отзывы: