background image

11

12

Connect the black and red test probe to cathode 
and anode of the diode to be tested, respectively. 
The meter will display the diode's forward bias 
voltage value. If the test probe polarity is reversed,
the meter will display “1”, which distinguishes the 
diode's cathode and anode.

3

When measuring diodes, to avoid injury or meter
damage, turn off the power to the circuit and 
discharge all capacitors. 

Warning

Battery test 

Place the function measuring range switch to the 
battery testing position. 
Insert the 

red probe to VΩmA input jack

. Insert the 

black probe to COM input jack. 
Connect free end of the red probe to positive and 
the free end of the black probe to negative end of 
the battery to be tested. 
Read the result from the LCD display. 

Don't input voltage higher than 60V DC or 30V AC, 
to prevent electric shock or meter damage. 
General specifications

Warning

• 

Operating environment and condition:  600V

  CAT. III, pollution grade: II.

 

  

Elevation < 2000 m

1

2

3

4

• 

Environmental temperature and humidity: 0~40°C, 

  <80% RH (do not use meter when temperature <10°C). 

• 

Storage temperature and humidity: -10~60°C and 

  <70% RH (remove the battery).

• 

Temperature coefficient: 0.1 Accuracy /°C(<18°C 

  or >28°C). 

• 

The maximum allowable voltage between 

  measurement end and ground: 600V DC or 600V
  AC RMS. 

• 

Fuse protection:  grade mA: fuse F200mA/500V 

  grade 10A: fuse F10A/500V

• 

Sampling rate: about 3 times/s. 

• 

Display: 3.5” digital LCD display. 

• 

Over-range indication: LCD will show “1”. 

• 

Low battery indication: When the battery voltage is

 

 lower than the normal operating voltage,

 

      

”will 

  

display on the LCD display. 

 

Input polarity indication: automatically display “-”. 

 

Power supply: AAA 1.5V batteries. 

 Accuracy Indicators

Accuracy: ±(% of r digits) with one year of 
warranty. Reference conditions: environmental 
temperature is from 18°C~28°C, relative humidity is 
not more than 80%.

Содержание MS8239A












Отзывы: