Masspower SUN-1000GTIL2-LCD Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 16

Masspower SUN-1000GTIL2-LCD Скачать руководство пользователя страница 10

Step4-Connect the solar panel cable to the GTIL DC input

4.3.5. Connect the Solar panel output to the DC power input of GTIL. Make sure

the disconnect switch/breaker of solar panel is off.

Before  connecting  the  solar  panel  cable,make  sure  that  the  solar  panel
disconnect  switch  or  DC  breaker  is  off  and  observe  correct  polarity  when
connecting the cable.Failure to follow will cause serious problem with the unit.Pls
read the manual booklet of the GTI included in the package for correct wire and
circuit  breaker/disconnect  switch  rating.Do  not  turn  on  the  DC  circuit
breaker/disconnect switch.

4.3.

6. Review all connections and make sure of the tightness of plugs and

connections. Re-check DC polarity connections of solar panel.

4.3.7. Turn on the 20A circuit breaker to power the Limiter Module.

4.3.8. In the LM, Press SET button below the LCD for a few seconds. The LCD
will light up and initialize.

«
...
8
9
10
11
12
...
»

Содержание SUN-1000GTIL2-LCD

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды