MASSEY FERGUSON MF 260 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 48

MASSEY FERGUSON MF 260 Скачать руководство пользователя страница 37

7

Chapter 19

Hydrostatic Power Steering System

37

Hydro-Static Power Steering System :

This system is installed in the MF385/385 4WD tractors, which allows the driver/operator
to control the steering system with ease. Hydro-static power steering system is a complete
power steering system in which there is no mechanical connection between the steering
wheel and the front wheels, which allows the steering wheel to be turned with only one or
two fingers. This tractor is especially suitable for working with front-end loaders.
In this oil system is supplied to the steering control unit through steering pump, due to
which controlled quantity of oil reaches the right and left sides by the steering cylinder
when the steering wheel is turned; and when the steering wheel is straight, the steering
unit bypasses the oil supply.

NOTE:

Always use the reputable and reliable oil in MF350/260/375/385/385 4WD Tractors

«
...
35
36
37
38
39
...
»

Содержание MF 260

















































Отзывы:

Нет отзывов