MASSEY FERGUSON MF 260 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 48

MASSEY FERGUSON MF 260 Скачать руководство пользователя страница 26

7

Chapter 12

Importance of Air-cleaner and Maintenance

26

2. Air-Cleaner Assembly

a. Air-Cleaner body (which contains a permanent filter)
b. Filter Element
c. Oil Bath

Oil is filled in the oil bath up to
the specified mark. Filter element
is placed over it, and then oil bath
is fitted with the air-cleaner.
When the air coming through the
pre-air cleaner makes contact with
the oil in the oil bath, the oil passes through the filter element up to the permanent filter
in the air-cleaner body, due to which the filter becomes covered with oil. The dust
particles in the air flowing through stick to the oily filter, and the cleansed air enters the
engine cylinder. Gradually, the oil becomes dirty due to this process.

Daily before use, remove the oil bath to check the oil level and its condition.
If the oil is below the required level, then fill the bath with more oil. If the oil is thick with
dust, then empty the oil, remove oil bath, air cleaner body, and filter element to clean
thoroughly with kerosene. After cleaning refill the oil bath up to the mark and attach to
the air-cleaner.

«
...
24
25
26
27
28
...
»

Содержание MF 260

















































Отзывы:

Нет отзывов