manualshive.com logo in svg

Masimo SET Radical-7, Руководство по обслуживанию

Поделиться
Скачать
Masimo SET Radical-7 Скачать руководство пользователя страница 18

Radical-7 Signal Extraction Pulse CO-Oximeter Service Manual 

5-4 

5.8.2 

Insert the non-dominant hand’s ring finger into the finger 
sensor. 

5.8.3 

Under %SpMET, a healthy, non-smoking individual would 
have a typical reading between 0-2% on the display. (These 
numbers are for reference only and should not be used for 
diagnostic purposes) 

5.9  PVI (Pleth Variability Index) Testing (If Applicable) 

Note:  This is performed as a functional test only. 

5.9.1 

Connect a Red Masimo SET Rainbow sensor to the Radical-
7 Handheld.  

5.9.2 

Insert the non-dominant hand’s ring finger into the finger 
sensor. 

5.9.3 

PVI will fluctuate depending on motion, perfusion, physiology 
and other factors, so there is no ‘normal’ value. If a number 
is displayed, then the PVI feature is functioning properly. 

5.10   Nurse Call Test  

Note:  Refer to Section 8 in this manual for connector pin outs noted in 
Sections 5.10 

5.10.1  Disconnect the patient cable or the Masimo SET Tester from 

the Radical-7 and turn the instrument on. Ensure that there 
are no audible alarms and that the audible alarms are not 
silenced.  

5.10.2  Connect the common lead of a digital multimeter to pin 12 

(Nurse Call - Common) of the Analog Output/Nurse Call 
Connector (see Service Manual, Troubleshooting, Section 8, 
Analog Output/Nurse Call Test) on the Radical-7. Connect 
the positive lead of the multimeter to pin 6 (Nurse Call - 
Normally Open) of the Analog Output/Nurse Call Connector 
and measure that the resistance is greater than 1 M

Ω

 (open 

circuit). 

5.10.3  Trigger an alarm on the monitor (e.g. by disconnecting a 

sensor after it was measuring data) and verify the resistance 
is < 20

Ω

. 

Содержание Radical-7









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды