Masimo SET Rad-57 Скачать руководство пользователя страница 51

Страница: 51 / 73

Rad-57 Signal Extraction Pulse CO-Oximeter Operator’s Manual

5-5

A l a r m s a n d M e s s a g e s

*available in upgraded Instrument

DISPLAY

REASON

SOLUTION

Err

System Fault

Return for service.
There are several error codes. All error

codes require return of the Instrument to an

authorized service center for repair. See

Section 9,

Service and Repair

for return

procedure.

RPL

Cbl

Defective cable

Replace cable

RPL

SeN

Sensor life expired

Replace sensor

RPL

ADH

Defective adhesive

sensor (resposable)

Replace adhesive sensor (resposable)

RPL

Reu

Defective reusable

sensor (resposable)

Replace reusable sensor (resposable)

INT

DET

(Blinking)

Interference detected

Ensure that the sensor is properly applied,

and cover the sensor site with opaque

material, if required.

INC

SeN

Incompatible sensor
Unrecognized sensor

Insert Masimo sensor

INC

Cbl

Incompatible cable
Unrecognized cable

Insert Masimo cable

INC

adH

Incompatible

adhesive sensor is

attached (resposable)

Attach compatible adhesive sensor

(resposable)

adH

No adhesive sensor is

attached (resposable)

Attach adhesive sensor (resposable)

SEN

000

No sensor uses

remaining

Insert new Masimo sensor

CBL

000

No cable uses

remaining

Insert new Masimo cable

Содержание Rad-57










































































Результаты поиска

Содержание Rad-57

Отзывы:

Masimo SET Rad-57, Руководство оператора, Страница: 51 / 73

Результаты поиска

Содержание Rad-57

Отзывы: