Masimo SET Rad-57 Скачать руководство пользователя страница 23

Страница: 23 / 73

Rad-57 Signal Extraction Pulse CO-Oximeter Operator’s Manual

2-3

S y s t e m D e s c r i p t i o n

Speaker

Provides audible indication of alarm conditions, pulse tone and feedback

for key-presses. Ensure the speaker is not covered or the Instrument is

placed face-down on bedding or other sound absorbing surface.

Visual Alarm

Indicator

Illuminates when any alrm condition exists. This indicator may not be

turned off or otherwise over-ridden.

Parameter/

Measurement Value

Display and Indicator

Displays parameter/measurement numeric values and indicates

parameter/measurement label.

PI Bar

The Perfusion Index provides an indication of the percentage of pulsatile

signal to non pulsatile signal. The bar is highest when the quality of the

perfused site is best.

Parameter/

Measurement Value

Display and Indicator

Displays parameter/measurement numeric values and indicates

parameter/measurement label.

Low SIQ

Flashes to indicate low

Signal IQ. Refer to

Section 4

Low Signal IQ

for details.

Alarm Silenced

Indicator

The indicator can flash or be solidly illuminated. Refer to

Alarm Silenced

Indicator

Section 5

for details.

Alarm Silence Button Push once to temporarily silence the alarm for 120 seconds. Push a

second time to return the Instrument to standard alarm monitoring

Up button
Down button

During saturation monitoring, use these buttons to adjust the volume of

the pulse beep tone.
Within the menu/setup system, these buttons are used to select values

within each menu option.

Содержание Rad-57










































































Результаты поиска

Содержание Rad-57

Отзывы:

Похожие инструкции для Rad-57

Бренды по названию

Популярные бренды

Masimo SET Rad-57, Руководство оператора

Результаты поиска

Содержание Rad-57

Отзывы:

Похожие инструкции для Rad-57

Бренды по названию

Популярные бренды