Masibus UC-12 Скачать руководство пользователя страница 56

Страница: 56 / 100

User Manual

P a g e

100

4.3.4 Pulse Setup

This Page is appears in

RUN



MENU



PULSE SETUP.

This  page  contains  parameters  related  to  Pulse  and  Frequency  like
Pulse  type,  Amplitude  (Vpp),  Unit,  Frequency,  Duty  Cycle  (%)  etc.
The  Description  of  the  Parameters  appear  on  this  page  is  given
below.

Parameter
Name

Description / Options

Pulse Type

Available Options:

Symmetric

Displays the symmetric
pulse type

Positive

Displays the Positive Pulse
type

Amplitude(Vpp)

Select the Amplitude of Pulse or Frequency

Unit

Frequency Unit

Available Options:
Hz
KHz
Cpm
Cph
1/Hz (s)
1/KHz (ms)

This Option appear only if Frequency mode is selected.

Frequency

To set Frequency.
This Option appear only if Pulse mode is selected.

Duty Cycle (%)

To set the Duty Cycle for Pulse and Frequency (01

– 99% 0 to 999999

pulses)

Содержание UC-12





































































































Результаты поиска

Содержание UC-12

Отзывы:

Похожие инструкции для UC-12

Бренды по названию

Популярные бренды

Masibus UC-12, Руководство пользователя

Результаты поиска

Содержание UC-12

Отзывы:

Похожие инструкции для UC-12

Бренды по названию

Популярные бренды