background image

 

 

2

Application 

Rammers are designed to compact loose soils and gravel to prevent settling and to provide a firm, 

solid base for the placement of footings, concrete slabs, foundations, gas piping works, water pipe 

works and cable backfill works, etc. 

 

Warnings for incorrect application and abuse 

 

Please do not use in such as following cases. It may cause damage because machine is likely to be 

unbalanced. 

l

 

Pile foundation 

l

 

Hard soil excessively compacted over normal condition 

l

 

Steep bank slope 

Tamping Rammer is to be used for compacting cohesive clay, gravels, and patching work on asphalt, 

etc. 

 

Structure 

The upper part is made up of Power source, Clutch, Connecting Rod and Operating Handle, Fuel 

Tank that connected via Shock Absorbing Rubber to body. Bottom end is made up of Spring Cylinder 

(Sliding part), Foot Plate that ramps body, Foot and Bellows that covers sliding part. 

 

Operating Safety 

Safety Notes 

This manual contains NOTES, CAUTIONS, and WARNINGS

 

which must be followed to prevent the 

possibility of improper service, damage to the equipment, or personal injury. 

Notes:

 

Notes contain additional Information important t a procedure.

 

CAUTION:

 Cautions provide information important to prevent Errors which could damage machine 

or components. 
 

                                   

WARNING 

 

             

Warnings warn of conditions or practices which could 

          lead to personal injury or death! 

           

Operating Safety 

Familiarity and proper training are required for the safe operation of equipment! Equipment operated 

improperly  or  by  untrained  personnel  can  be  dangerous!  Read  the  operating  instructions  and 

familiarize yourself with the location and proper use of all instruments and controls. Inexperienced 

operators should receive instruction from someone familiar with the equipment before being allowed 

to operate the rammer. 

 

NEVER 

operate rammer in applications for which it is not intended. 

NEVER 

allow improperly trained personnel to operate rammer. 

NEVER 

touch hot muffler, engine cylinders, or cooling fins. Burns will result. 

NEVER 

use accessories or attachments which are not recommended by MASALTA for rammer. 

Damage to rammer and/or injury to user may result. 

NEVER 

leave a running machine unattended.

 

Содержание EMR70H















Отзывы:

Похожие инструкции для EMR70H