Marzocchi MAX COMP + ETA - 105 Скачать руководство пользователя страница 1

Страница: 1 / 45

MX Comp + ETA

1/45

Features

TECHNICAL CHARACTERISTICS

Fork with Ø30 mm legs with spring and
hydraulic rebound damping.

Adjustment of the hydraulic rebound
braking through the adjuster in the right leg.

Adjustment of the air preload on both legs.

The stanchion tubes are pressed into the
crown with a cryogenic process.

New sliding system to improve the stiffness
and operation.

Magnesium alloy cast one-piece assembly,
CNC machined for lighter weight and more
stiffness.

Components subjected to friction are
lubricated and cooled by means of a
special oil.

Steer tube:

steel or (optional) aluminium,

1-1/8", threadless.

Crown:

BAM® aluminium alloy forged and

CNC machined.

Stanchions:

anodised aluminium.

Springs:

constant pitch.

Sliding bushes:

made of friction free and

wear free material.

Seals:

computer designed oil seals that

guarantee the maximum seal in any
condition.

Oil:

special formulated oil that prevents

foam and keeps the viscosity unchanged
while offering high performance; free from
static friction.

Dropout type:

Standard.

Disk brake mount:

XC International

Standard for 6" disk.

V-Brake fit.

BAM®: Bomber Aerospace Material:
special alloy coming from the aerospace
industry.

Содержание MAX COMP + ETA - 105














































Результаты поиска

Содержание MAX COMP + ETA - 105

Отзывы:

Похожие инструкции для MAX COMP + ETA - 105

Бренды по названию

Популярные бренды

Marzocchi MAX COMP + ETA - 105, Руководство пользователя

Результаты поиска

Содержание MAX COMP + ETA - 105

Отзывы:

Похожие инструкции для MAX COMP + ETA - 105

Бренды по названию

Популярные бренды