background image

Failure to add oil to the gasoline or failure to 

mix oil with the gasoline at the appropriate 

ratio will cause major engine damage which will 

void your warranty. 

For your fuel  premix,  only use a quality  oil 

designed  for  2-cycle  air  cooled  engines. 

Maruyama 50:1 2-cycle Oil is formulated  to 

meet  the requirements  of high-performance, 

air-cooled two-cycle engines. 

Fuel Mixture 

The fuel: oil ratio is 50 parts gasoline to 

part oil or 

50:1. 

Note: 

50:1 

Never use a mixing ratio less than 

50:1  regardless of the oil  package 

mixing instructions.  Ratios less the 

50:1, 

(for example, 

60:1, 

80:1, 

100:1), 

reduce the amount  of lubrication to 

the  internal  moving  parts  of the 

engine and can cause damage. 

Fuel Mixture Chart 

Gasoline 

50:1  2-cycle oil 

1  gallon 

2.6oz. 

2gallons 

5.2oz. 

5 gallons 

12.8 oz. 

Mixing Instructions 

IMPORTANT:  Never mix  gasoline and  oil 

directly in the Trimmer fuel tank. 

J.

Always  mix  fuel 

and 

oil  in  a clean container

approved for gasoline.

2. Mark the container to identify it as fuel mix for

the Trimmer.

3. Use regular unleaded gasoline and fill the contain­

er with half the required amount of gasoline.

4. Pour the correct amount  of oil  into the container

then add the remaining amount of gasoline.

5. Close the container tightly and shake it momentar­

ily to evenly  mix the oil and  the gasoline before

filling the fuel tank on the Trimmer.

6. When  refilling  the Trimmer fuel  tank,  clean

around the fuel tank cap to prevent dirt and debris

from entering the tank during cap removal.

7. Always  shake  the premix fuel  container momen­

tarily before filling the fuel tank.

8. Always use  a spout  or funnel  when fueling to

reduce fuel spillage.

9. Fill the tank only to within  1/4-1/2 inch (6 mm-13

mm) from the top of the tank.  Avoid filling to the

top of the tank fillerneck.

Starting And Stopping 

Before Starting The Engine 

l. Fill  the fuel  tank  as  instructed in  the Before

Operation section of this manual.

2. Rest the Trimmer on the ground.

3. Make sure the cutting attachment is clear of any

broken glass, nails, wire, rocks or other debris.

4. Keep all bystanders, children and  animals  away

from the working area.

-14-

Содержание BCL2250

























Отзывы: