Maruyama BC3601H-RS Скачать руководство пользователя страница 9

Страница: 9 / 24

＿

IMPORTANT: Make sure the trimmer head is for LEFT-

HAND ROTATION (counterclockwise) as

viewed from the operator’s position, and

that the trimmer head adapter is a female,

M10 left-hand thread.

1. Remove the blade nut and stabilizer from the attaching shaft

out of the gearcase. (Keep the blade nut and stabilizer )

Note: The blade nut has left-hand thread.

2. Align the hole in the boss adapter with the hole in the

gearcase.

3. Insert the Ø6 mm pin into the hole in the boss adapter and

the hole in the gearcase to lock the attaching shaft.

4. Thread the trimmer head adapter into the attaching shaft,

then tighten the trimmer head by hand.

Note: The trimmer head adapter has left-hand thread.

5. Remove the Ø6mm pin from the boss adapter and gearcase.

Installing Cutting Attachment

Trimmer Head

WARNING

POTENTIAL HAZARD

・

If the trimmer head is not adequately tightened, it can come loose from the Trimmer/ Brushcutter

during use.

WHAT CAN HAPPEN

・

This may cause damage to property or personal injury.

HOW TO AVOID THE HAZARD

・

Make sure the trimmer head is securely fastened to the attaching shaft in the gearcase.

Brushcutter Blade

WARNING

POTENTIAL HAZARD

・

If the Brushcutter blade is not adequately tightened, it can come loose from the Brushcutter

during use.

WHAT CAN HAPPEN

・

This may cause damage to property or personal injury.

HOW TO AVOID THE HAZARD

・

Make sure the Brushcutter blade is securely fastened to the attaching shaft in the gearcase.

CAUTION

POTENTIAL HAZARD

・

Brushcutter blade is sharp.

WHAT CAN HAPPEN

・

Contact with sharp blade can cause personal injury.

HOW TO AVOID THE HAZARD

・

Wear gloves when you handle the blade.

Trimmer Head

Holding Tool

(Ø6mm Pin)

Gearcase

Left-hand

thread

Trimmer Head

Adapter

Attaching

Shaft

Boss

Adapter

Clamping

Washer

Содержание BC3601H-RS

























Результаты поиска

Содержание BC3601H-RS

Отзывы:

Бренды по названию

Популярные бренды

Maruyama BC3601H-RS, Руководство владельца/оператора

Результаты поиска

Содержание BC3601H-RS

Отзывы:

Бренды по названию

Популярные бренды