Maruyama BC3601H-RS Скачать руководство пользователя страница 20

Страница: 20 / 24

＿

Cylinder Cooling Fins

Maintenance Interval

・

The cylinder cooling fins should be cleaned after every

25hours of operation, or once a week, whichever comes

first.

・

Air must flow freely around and through the cylinder

cooling fins to prevent engine overheating. Leaves, grass,

dirt and debris buildup on the fins will increase the

operating temperature of the engine, which can reduce

engine performance and shorten engine life.

Spark Plug

Maintenance Interval

・

The spark plug should be removed from the engine and

checked after each 25 hours of operation.

・

Replace the spark plug after every 100 hours of operation.

Spark Plug Maintenance

1. Twist the high tension lead boot on the spark plug back

and forth a couple of times to loosen the boot, then pull

the boot off of the spark plug.

2. Remove the spark plug.

3. Clean the electrodes with a stiff brush.

4. Adjust the electrode air gap to 0,6-0,7 mm.

5. Replace the spark plug if it is oil-fouled, damaged, or if the

electrodes are worn down.

6. Do not over tighten the spark plug when installing. The

tightening torque is 10,7-16,6 N·m.

0,6-0,7mm

Cooling Fins Cleaning

1. Remove the air filter cover.

2. Remove the plug cap.

3. Loosen the knob and lift off the top cover. Clean all dirt

and debris from the cooling fins and from around the

cylinder base. Reinstall the top cover and the air filter

cover.

Air Filter Cover

Cooling

Fins

Plug Cap

Top Cover

Knob

Содержание BC3601H-RS

























Результаты поиска

Содержание BC3601H-RS

Отзывы:

Бренды по названию

Популярные бренды

Maruyama BC3601H-RS, Руководство владельца/оператора

Результаты поиска

Содержание BC3601H-RS

Отзывы:

Бренды по названию

Популярные бренды