Maruyama BC200H Скачать руководство пользователя страница 16

POTE NTIAL HAZARD

• Petrol contains gasses that can build up pressure inside a fuel tank.

WHAT CAN HAPPEN

• fuel can be spraye d on  you wh en removing fuel tank cap.

HOW TO AVOID THE HAZARD

• Remove fuel tank cap slowly to avoid inju ry from fuel spray.

POTE NTIAL HAZARD

• In certain conditions petrol is extremely ammable and highly explosive. 

WHAT CAN HAPPEN

• A fire or explosion from petrol can burn you, others and cause property

damage. 

HOW TO AVOID THE HAZARD

• Use a funnel and  ll the fuel tank outdoors, in an open area, when the

engine is cold.

Wipe up any petrol that spills.

• Do not ll the fuel tank completely. Add petrol to the fuel tank until the

level is 10mm below the bottom of the ller neck. This empty space in the

tank allows petrol to expand.

• Never smoke when handling petrol, and stay away from an open ame

with petrol in an approved container and keep it out of the reach of

children.

• Do not mix fuel for more than two month use.

OIL AND FUEL

1. Mix and pour fuel outdoors and where  there are no spark s or  ames.

2. Always shut off the engine  before refueling . Never  remo ve the fuel tank cap

while  the engine  is running  or immedia tely after stopping  the engine .

6. Wipe up any spilled fuel before starting the engine.

7. Move the Brushcutte r at least 3 m away from the fueling location and fuel

storage container before starting the engine.

BEFORE OPERATION

WARNING

DANGER

3m

3. Always open the fuel tank cap slowly to release any possible pressure inside

the tank. 

4. Do not over fill the fuel tank. Stop filling 10 ~ 20 mm from the top of the tank.

5. Tighten the fuel tank cap carefully but firmly after refilling

ВОЗМОЖНАЯ ОПАСНОСТЬ

• 

Бензин содержит газы, которые поднимают давление в топливном 

  баке.

ЧТО МОЖЕТ ПРОИЗОЙТИ

• Топливо может выплеснуться на вас при открытии крышки 

  топливного бака.

КАК ИЗБЕЖАТЬ ОПАСНОСТИ

• 

Снимайте крышку топливного бака медленно, чтобы избежать

  травм в результате разбрызгивания топлива.

ВОЗМОЖНАЯ ОПАСНОСТЬ

• При определенных условиях бензин чрезвычайно горюч и 

  взрывоопасен.

ЧТО МОЖЕТ ПРОИЗОЙТИ

• Возгорание или взрыв бензина может привести к ожогам оператора 

  и других людей, а также к повреждению имущества.

КАК ИЗБЕЖАТЬ ОПАСНОСТИ

• Пользуйтесь воронкой и заполняйте топливный бак на улице, 

  на открытой местности при холодном двигателе. Удалите весь 

  пролитый бензин.

• Не наполняйте топливный бак полностью. Заливайте бензин в

  топливный бак до уровня на 10 мм ниже горловины бака. Это пустое

  пространство в баке позволяет бензину расширяться.

• При работе с бензином не курите, находитесь вдали от источников

  открытого огня, храните бензин в специальной емкости в 

  недоступном для детей месте.

• Смешивайте топливо в объеме, рассчитанном не более чем на два

  месяца использования.

МАСЛО И ТОПЛИВО

1. Смешивайте и заливайте топливо вне помещений, в местах,

    защищенных от искр и огня.

2. Перед заправкой обязательно выключайте двигатель. Запрещается 

   снимать крышку топливного бака при работающем двигателе или сразу 

   после остановки двигателя.

5. После заправки аккуратно, но плотно затяните крышку топливного

   бака.

6. Перед запуском двигателя удалите пролитое топливо.

7. Перед запуском переместите кусторез на расстояние не менее 3 м

    от места заправки топивом и емкости для хранения топлива.

ПЕРЕД НАЧАЛОМ РАБОТЫ

ОСТОРОЖНО

ОПАСНОСТЬ

3. Открывайте крышку топливного бака медленно, чтобы стравить 

    давление внутри бака.

4. Не переполняйте топливный бак. Прекратите заполнение за 

  10-20 мм до горловины бака.

ПОТЕНЦІЙНА НЕБЕЗПЕКА

Бензин містить гази, які можуть утворювати тиск всередині

    

паливного бака.

МОЖЛИВІ НАСЛІДКИ

На користувача може розбризкатися паливо під час відкриття

   

кришки паливного бака.

ЯК УНИКНУТИ НЕБЕЗПЕКИ

Повільно відкривайте кришку паливного бака, щоб уникнути

    

пошкодження через розбризкування палива.

ПОТЕНЦІЙНА НЕБЕЗПЕКА

За певних умов бензин є дуже займистою і вибухонебезпечною

речовиною.

МОЖЛИВІ НАСЛІДКИ

Пожежа або вибух через бензин можуть призвести до опіків

користувача та інших робітників, а також призвести до пошкодження

майна.

ЯК УНИКНУТИ НЕБЕЗПЕКИ

Використовуйте лійку та заповнюйте паливний бак на відкритому повітрі,

    коли двигун охолонув.

    Ретельно витріть бензин, якщо його пролито.

Не заповнюйте паливний бак повністю. Додавайте бензин у паливний бак до 

   

рівня 10 мм нижче нижнього краю заливної горловини. 

   

Вільний простір у паливному баку дає бензину можливість розширюватися.

Забороняється палити під час роботи із бензином. Зберігайте бензин на

    відстані від відкритого вогню у спеціальних контейнерах та у недосяжному

    для дітей місці.

Не змішуйте паливо для використання впродовж періоду більше двох місяців.

МАСЛО ТА ПАЛИВО

1. Змішуйте й наливайте паливо на вулиці, де немає полум’я та іскор.

2. Обов’язково вимикайте двигун перед заправленням. Не знімайте кришку

    паливного бака під час роботи двигуна або одразу після зупинки двигуна.

5. Обережно, але щільно закрийте кришку паливного бака після

    заправлення.

6. Перед запуском двигуна витріть пролите паливо.

7. Перш ніж запускати двигун, перемістіть кущоріз на відстань принаймні 3 м

    від місця заправки та контейнера для зберігання палива.

ПЕРЕД ЕКСПЛУАТАЦІЄЮ

ПОПЕРЕДЖЕННЯ

НЕБЕЗПЕКА

3. Завжди відкривайте кришку паливного бака повільно, щоб послабити

    можливий тиск всередині бака.

4. Не переповнюйте паливний бак. Зупиніть заповнювання за 10 ~ 20 мм

    від верхнього краю бака

<14>

ENGLISH

РУССКИЙ

УКРАЇНСЬКА

3m

Содержание BC200H

































Отзывы: