background image

 28

MAC Allure Wash PC User Guide

PERSONALITY
(continued)

TUNGSTEN 
EMULATOR

ON

Color temperature and dimming 
characteristics emulate tungsten lamp 
behavior

OFF

FOCUS 
TRACKING

FAR

Focus adjusts to match zoom: optimized 
for long range projection

MEDIUM

Focus adjusts to match zoom: optimized 
for mid-range projection

NEAR

Focus adjusts to match zoom: optimized 
for close range projection

DISABLED

Focus tracking function disabled

COLOR MODE

EXTENDED COLOR

Color mixing optimized for saturation

CALIBRATED

Color mixing optimized for even color 
rendition across fixtures

VIDEO 
TRACKING

ENABLED

Color fading optimized for speed of color 
changes

DISABLED

Color fading optimized for smoothness

DMX RESET

ON

Fixture can be reset via DMX

OFF

Fixture cannot be reset via DMX (note that 
this menu item can be overridden: see 
DMX protocol)

EFFECT 
SHORTCUT

ON

Effects take shortest route during 
changes, crossing open positions if 
necessary

OFF

Effects avoid open positions during effects 
changes

COOLING MODE

CONSTANT FAN FULL

Fans optimized for maximum light intensity, 
fans run at full speed, light intensity 
reduced if necessary to keep fixture within 
temperature limits

CONSTANT FAN MEDIUM

Fans run at medium speed, light intensity 
reduced if necessary to keep fixture within 
temperature limits

CONSTANT FAN LOW

Fans run at low speed, light intensity 
reduced if necessary to keep fixture within 
temperature limits

CONSTANT FAN ULOW

Fans optimized for lowest noise, fans run 
at ultra-low speed, light intensity reduced if 
necessary to keep fixture within 
temperature limits

REGULATE FANS

Compromise between light intensity 
and quietness, fan speed 
temperature-regulated, light intensity 
only reduced if fans reach full speed 
and further action necessary to keep 
fixture within temperature limits

DISPLAY

DISPLAY SLEEP

10 MINUTES

Display goes into sleep mode 10 minutes 
after last key press

5 MINUTES

Display goes into sleep mode five minutes 
after last key press

2 MINUTES

Display goes into sleep mode two 
minutes after last key press

ON

Display permanently on

DISPLAY 
INTENSITY

10 

...

 100 %

Set display intensity in % (default = 

100

)

DISPLAY 
ROTATION

NORMAL

 / 

ROTATE 180

Display orientation 

normal

 or rotated 180°

DISPLAY 
CONTRAST

...

100

Adjust contrast of display (default = 

41

)

Menu level 1

Menu level 2

Menu level 3

Menu level 4

Notes (Default settings in bold print)

Table 4: Control menus

Содержание MAC Allure Wash PC



































Отзывы: