-!24).9!,%
'"
6) Specification
Speed:
20.000 A4 sheets/h,
depending on paper quality
Paper Sizes:
Max. Width 305 mm (12”)
Max. Length 432 mm (17”)
Min. Width 90 mm (3.55”)
Min. Length 100 mm (4”)
Number of fold plates:
2
Fold lengths:
Plate I:
Max.: 324 mm
Min.: 40mm
Plate II:
Max.: 216 mm
Min.: 40mm
Paper weights:
Min. 50 g/m²
Max. 180 g/m²
Noise emission:
75 dB(A), 80 g/m², Paper letterfold
at a speed of 10,000/h
Connected loads:
230 VAC, 50 Hz, 2 A
100 VAC, 50/60 Hz, 3 A
120 VAC, 60 Hz, 3 A
Environmental conditions
: Room temperature: 13°C - 35°C
Humidity: 20 % - 80 %,
non-condensing
Weight:
43 kg
Dimensions:
Length 860 mm
Width 640 mm
Height 430 mm
-- STACKER ERROR --
DONE - Enter
There is a problem with the stacker rollers. Try pressing
Enter
; the
problem may clear itself automatically.
If this does not help, turn power off and remove the fold plate assembly as
described on page 15. This gives access to the stacker drive mechanisms
on the underside of the stacker table.
Locate the stacker motor and turn the small drive gear on the motor shaft.
This will move the stacker rollers.
Turn the gear in the direction that will move the stacker rollers away from
the extreme end of their travel. Keep turning until the stacker rollers have
moved about 2 mm (3/4”) away from the end of their guide slots in the
stacker table.
Refit the fold plate assembly as described on page 25 and turn power
back on. The stacker rollers will move to their proper position and the
display will return to the running mode.
If the rollers return to their extreme position and the “STACKER ERROR”
message appears again, try the above procedure once or twice more. If
the fault persists, call the service engineer for assistance.
-- FOLD PLATE ERROR --
DONE - Enter
This error occurs when the fold plate stop is prevented from travelling
along its guide screw by an obstruction like an accumulation of dirt and
paper dust.
Try pressing
Enter
. The fault may be cleared automatically and the
display will revert to the normal running mode. If this does not help, turn
power off and remove the fold plate assembly as described under the
heading of 4.9.
Place the fold plate assembly on its side. Working through the openings
in each fold plate, try to turn the long guide screw on which the fold plate
stop travels. Turn the screw several turns each way to clean out any
paper dust which may have accumulated in the brass nut of the paper
stop.
If you find that the paper stop has travelled to the very end of its travel at
either end, turn the screw so that the stop is at least 2 mm (3/4”) away
from the extreme position.
Refit the fold plate assembly as described under the heading of 4.9
and turn power back on. The fold plate stops will move to their proper
positions and the display will return to the running mode.
If the “FOLD PLATE ERROR” message appears again, try the above
procedure once or twice more. If the fault persists, call the service
engineer for assistance.
-- LIMIT SWITCH F.P.1 --
DONE - Enter
-- LIMIT SWITCH F.P.2 --
DONE - Enter
These error messages mean that the stop in either fold plate 1 (F.P.1)
or fold plate 2 (F.P.2) has moved to the very end of its travel and has
operated the emergency limit switches at those positions.
Follow the procedure for “FOLD PLATE ERROR” above to clear this
condition.
Содержание 2601
Страница 66: ... 24 9 ...
