Martin Audio MA4.8Q Скачать руководство пользователя страница 29

Страница: 29 / 31

Q Series Operation Manual

9 TEChNICAL sPECIFICATIONs

Following are the

Q Series

technical specifications. These figures are accurate at the time of printing but

please note that all figures are subject to change without notice. For the most accurate and current information
available, please visit

www.martin-audio.com.

Individual values for

Q Series

amplifiers

MA6.8Q MA4.8Q

Number of channels per amplifier 4 4
Total Power Limit

6800 W 4800 W

Max. output voltage per channel

100 V

rms

100 V

rms

Max. output current per channel

24,5 A

rms

17,5 A

rms

Max. continuous output power all 4 channels driven at VPL: 141V and Gain: 35dB

16 ohms (per ch.) 650 W 625 W

8 ohms (per ch.) 1200 W 1000 W

4 ohms (per ch.) 1700 W 1200 W

2 ohms (per ch.) 1200 W 600 W

Hi-Z: 70V/100V (per ch.) 1600 W 900 W

Mains connector, 230V CE version 16A / CEE7 16A / CEE7

Mains connector, 115V ETL version 20 A / 5-20P 20 A / 5-20P

Maximum mains current consumption, 230V version 11.2 A 8,7 A

Maximum mains current consumption, 115V version 22.4 A 17,4 A

PAL

reduces the maximum output power keeping the power supply in safe operating area and/or

preventing excessive current draw tripping the mains breaker. Refer to user’s manual.

The Voltage Peak output values translate to rms Voltage for a sine wave as: peak/1.41 = Vrms.
E.g. 141V peak is

100V

rms

and 100V peak is

70V

rms

. This means that the outputs can be set for

high impedance loads without the use of an external transformer.

Single channel operation at 2 ohms and bridged mode at 4 ohms are not recommended.

Separate 230 V or 115 V versions available. Not selectable on the amplifier.

Содержание MA4.8Q
































Результаты поиска

Содержание MA4.8Q

Отзывы:

Похожие инструкции для MA4.8Q

Бренды по названию

Популярные бренды

Martin Audio MA4.8Q, Руководство пользователя

Результаты поиска

Содержание MA4.8Q

Отзывы:

Похожие инструкции для MA4.8Q

Бренды по названию

Популярные бренды