background image

19

WARRANTY

General

The E1300 Power amplifier is warranted to be free from defects in
components and factory workmanship under normal use and service, for a
period of one year from the date of original purchase. During the warranty
period, MARTIN AUDIO LTD or its nominated agents, will undertake to
repair or at its discretion, replace this product at no charge to its owner,
when failing to perform as specified, provided the unit is returned
undamaged, in its original packaging, shipping pre-paid, to the factory,
distributor or authorised service facility.

This warranty shall be null and void, if the product is subjected to:
1. Repair work or alteration by persons other than those authorised by

MARTIN AUDIO LTD or its agents.

2.  Shipping accidents, act of God, war, civil insurrection, misuse, abuse

operation with incorrect AC voltage, operation with faulty associated
equipment, exposure to inclement weather conditions and normal wear
and tear. Units, on which the serial number has been removed or
defaced, will not be eligible for warranty service

3.  MARTIN AUDIO LTD shall not be responsible for any incidental or

consequential damages, with respect to the products warranted.

MARTIN AUDIO LTD reserve the right to make changes or improvements in
design or manufacturing, without assuming any obligation to change or
improve products previously manufactured.

This warranty is exclusive and no other warranty is expressed or implied.
This warranty does not affect your statutory rights.

International
Please contact your supplier for this information, as rights and disclaimers
may vary from country to country.

Technical assistance and services
International

If your Martin Audio product needs repair, contact your Martin Audio dealer
or distributor, or contact Martin Audio by fax or email to obtain the location
of the nearest dealer or distributor.
Telephone: + 44 (0) 1494 535312
Fax: + 44 (0) 1494 438669
E-mail: [email protected]
www.martin-audio.com

Martin Audio – E1300 Amplifier

E

NGLISH

21

All material © 2007. Martin Audio Ltd. Subject to change without notice.

Содержание E1300


























Отзывы: