manualshive.com logo in svg

Martel BETAGAUGE 330, Справочное руководство

Поделиться
Скачать
Martel BETAGAUGE 330 Скачать руководство пользователя страница 45

15. Warranty

Martel Electronics Corporation warrants all products against material defects and
workmanship for a period of twelve (12) months after the date of shipment. Problems or
defects that arise from misuse or abuse of the instrument are not covered. If any product
is to be returned, a “Return Material Authorization” form can be obtained from our website
www.martelcorp.com under customer service. You can also call 1-800-821-0023 to have a
form faxed. Martel will not be responsible for damage as a result of poor return
packaging. Out of warranty repairs and recalibration will be subject to specific charges.
Under no circumstances will Martel Electronics be liable for any device or circumstance
beyond the value of the product.

16. Maintenance

16.1 Replacing Batteries

Replace batteries as soon as the battery indicator turns on to avoid false measurements.
If the batteries discharge too deeply the BETA 330 will automatically shut down to avoid
battery leakage.

Note

: Use only AA size alkaline or Lithium batteries or optional rechargeable NiMh cells.

16.2 Cleaning the Unit

Warning

To avoid personal injury or damage to the calibrator, use only the specified replacement
parts and do not allow water into the case.

Caution

To avoid damaging the plastic lens and case, do not use solvents or abrasive cleansers.

Clean the calibrator with a soft cloth dampened with water or water and mild soap.

16.3 Valve Cleaning Procedure

Occasionally, the BetaGauge 330 may not work properly due to dirt or other
contamination of the internal valve assembly. Use the following procedure for cleaning the
valve assembly. If this procedure does not fix the problem, a repair kit (part number
1010043) may be ordered.

1.   Using a small screwdriver, remove the 2 valve retention caps located in the battery

compartment area (see Figure 1, page 4).

2.   After the caps have been removed, gently remove the spring and 

o-ring assembly.

3.   Set aside the valve assemblies in a safe area and clean out the valve body using a

cotton swab soaked in IPA (isopropyl alcohol).

4.   Repeat the process several times using a new cotton swab each time until there is no

remaining evidence of contamination or dirt.

5.   Operate the pump handles several times and recheck for contamination.

43

Содержание BETAGAUGE 330

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды