Martel BETAGAUGE 330 Скачать руководство пользователя страница 34

Страница: 34 / 48

IO_STATE

Set the calibrator's mA state.

IO_STATE?

Return the calibrator's mA state.

LOCAL

Returns user to manual operation of the calibrator

LOCKOUT

Locks out the keypad of the calibrator in remote operation

LO_ERR

Sets the 0% of span limit for percent error mode

LO_ERR

Returns the 0% of span limit for percent error mode

MOTOR_ON

Turns the motor on.

MOTOR_OFF

Turns the motor off.

MOTOR?

Returns the current state of the Hart resistor

OHMS?

Returns ohms value measured from the RTD

OUT

Set the calibrator to output the requested current.

OUT?

Returns the value of the current being simulated.

PRES_UNIT

Set the pressure unit for the indicated display

PRES_UNIT?

Returns the pressure from the indicated display

PUMP_LIMIT

Sets the approximate value at which the pump will turn off.

PUMP_LIMIT?

Returns the approximate value at which the pump will turn off.

REMOTE

Puts the calibrator in remote mode

RTD_TYPE

Sets the RTD type

RTD_TYPE?

Returns the RTD type

SIM

Set the calibrator to simulate the requested current.

SIM?

Returns the value of the current being simulated.

ST_CLOSE?

Returns pressure value at which the switch closed

ST_DEAD?

Returns pressure value of the deadband of the switch

ST_OPEN?

Returns pressure value at which the switch opened

ST_START

Starts a switch test

TEMP_UNIT

Set the RTD to read in °F or °C on the indicated display

TEMP_UNIT?

Returns the unit the RTD is set to read on the indicated display

VAL?

Returns the measured values

ZERO_MEAS

Zeros the pressure module

ZERO_MEAS?

Returns the zero offset of the pressure module

Table 7: Parameter units

Units Meaning

CEL

Temperature in degrees Celsius

CUSTOM

Custom RTD type

DCI

Current function

DCV

Voltage measure function

EXT

External pressure measurement function

FAR

Temperature in degrees Fahrenheit

Содержание BETAGAUGE 330

















































Результаты поиска

Содержание BETAGAUGE 330

Отзывы:

Бренды по названию

Популярные бренды

Martel BETAGAUGE 330, Справочное руководство

Результаты поиска

Содержание BETAGAUGE 330

Отзывы:

Бренды по названию

Популярные бренды