background image

Safety Instructions 

 

Before putting the device into use, please read with care the information given in this user 
manual, which contains important instructions for proper installation, use and maintenance 
of the device. 
 
Marsden/the manufacturer shall not be liable for damages arising from failure to heed the 
following instructions: 

  When using electrical components under increased safety requirements, always 

comply with appropriate regulations. 

  Inappropriate installation/use will render the warranty null and void. 

  Ensure the voltage marked on the power supply unit matches your mains supply. 

  This device is designed for use indoors. 

  Observe the permissible ambient temperatures for use. 

  The device meets the requirements for electromagnetic capability. Do not exceed 

the maximum values specified in the applicable standards. 

  Batteries should be kept away from small children. If swallowed, promptly seek 

medical assistance. 

 
If you have any problems, contact Marsden/your local dealer/your service partner. 

 

Cleaning 

 

  We recommend using alcohol-based wipes or similar when cleaning the scale. 

  Please do not use large amounts of water when cleaning the scale as this will 

cause damage to the electronics. Please refrain from using corrosive liquids or high 
pressure washers. 

  Always disconnect the scale from the mains power supply before cleaning. 

 

Maintenance 

 

  The scale does not require any routine maintenance. However, we recommend 

checking the scale

’s accuracy at regular intervals. If any inaccuracies occur, please 

contact your local dealer or service partner. 

  If you are in the UK, contact Marsden on 01709 364296 about service and 

calibration contracts. 
 

 

Disposing of the Scale 

 

  This product is not to be treated as regular household waste, but should be handed 

in to an electrical/electronic equipment recycling centre. 

  You can obtain further details from your local council, your municipal waste disposal 

company or from where you purchased the product. 

 
 

Page 5 

Содержание M-550BT
















Отзывы: