MARLO MATD 9500 XT Скачать руководство пользователя страница 23

Страница: 23 / 71

Page

Timer Operation

Valve State:

CHG (Change of State)

CHG will be displayed when the lower drive changes from one state to another in dual piston valves.

INI (Initializing)

INI will display on the screen for 30 to 45 seconds when initializing after a power failure reset or programming.

RGQ (Regeneration Queued)

RGQ indicates that the reserve has been entered in a delayed system and regeneration has been queued.

When in the main screen, press the Shift button to toggle service (SRV) with RGQ.

Service (SRV)

SRV will display when the unit is in service.

LED Status Lights:

Blue LED:

Illuminates while the unit is in service and no errors exist. The unit will always be in service unless a

regeneration trigger has occurred (green LED light will be displayed).

Green LED:

Illuminates when the unit is in Regeneration mode, unless an error condition exists.

Red LED:

Illuminates when there is an error.

Flow Indicator:

A rotating line (appearing as a rotating star shape) will display on the screen when ﬂow is going through the

the meter.

42138_REVA

MAT

9500 XT MANUAL

Содержание MATD 9500 XT








































































Результаты поиска

Содержание MATD 9500 XT

Отзывы:

Бренды по названию

Популярные бренды

MARLO MATD 9500 XT, Руководство пользователя

Результаты поиска

Содержание MATD 9500 XT

Отзывы:

Бренды по названию

Популярные бренды