MARLO MATD 9500 XT Скачать руководство пользователя страница 13

Страница: 13 / 71

Page

MOUNTING CONTROL VALVE ASSEMBLY

1. On the right side tank, verify that the distributor riser pipe is not plugged.

2. Lubricate the distributor o’ring on the bottom of the control valve with silicone.

3. Screw the control valve into top opening of tank making sure the distributor riser pipe slides

easily through the distributor o’ring. Care must be taken not to “nick” this o’ring as hard

water leakage could result.

4. Tighten down the control valve to ensure positive o’ring seal at top of tank.

5. On the left side tank, verify that the distributor riser pipe is not plugged on the second

softener tank.

6. Lubricate the distributor o’ring on the bottom of the second tank adapter assembly with

silicone.

7. Screw the second tank adapter assembly into top opening of tank making sure the distributor

riser pipe slides easily through the distributor o’ring. Care must be taken not to “nick” this

o’ring as hard water leakage could result.

8. Attach the second tank adapter assembly to the control valve.

9. A grounded electric receptacle is required for the control valve.

MOUNTING WATER METER ASSEMBLY

1. Locate the water meter. The water meter has a flow arrow stamped on it. The flow arrow on

the meter should be pointing away from the control valve. Attach the meter to the control

valve's water outlet.

2. The digital water meter is connected to the control valve with a transducer wire cable. Attach

the one end of the cable with a small rectangular box on it into the dome of the meter.

Secure the transducer with attached screw clamp on the top of the meter dome. Wire the

other end of this cable to the control valve's terminal strip. Reference the electrical wiring

diagram located in the back of this manual.

Содержание MATD 9500 XT








































































Результаты поиска

Содержание MATD 9500 XT

Отзывы:

Бренды по названию

Популярные бренды

MARLO MATD 9500 XT, Руководство пользователя

Результаты поиска

Содержание MATD 9500 XT

Отзывы:

Бренды по названию

Популярные бренды