background image

KLEAR FLO II  

AUTOMATIC WATER CONDITIONERS

5

Phone: (262) 681-1300 • Web: www.Marlo-Inc.com • E-mail: [email protected]

User Display Settings

When the system is operating, several displays may be shown. 
Pressing NEXT will alternate between the displays. One of the 
displays is the current time of day. CAPACITY REMAINING 
is the gallons that will be treated before the system goes through 
a regeneration cycle.  Pressing DOWN while in the Capacity 
Remaining display will decrease the capacity remaining in 
10 gallon increments and will also increase the volume used 
impacting the recorded values in Diagnostics. 
DAYS TO A REGEN is the number of days left before the system 
goes through a regeneration cycle. Pressing UP or DOWN while in  
this screen will temporarily increase or decrease the displayed value by 
1 day. Another display shows the current treated water  flow rate through 
the system. Contact information will be displayed if it was edited. 

 The fifth display will show either DP or HOLD if  

the dP switch is closed. If the system has called for a 
regeneration that will occur at the pre-set time of regeneration, 
the words REGEN TODAY will alternate with the header on the 
display. If a water meter is installed, GPM  flashes (and alternates 
with the  flow rate) on the display when water is being treated (i.e. 
water is  flowing through the system).   

GPM and  flow rate 

will flash while water 

is being treated.

Set Time of Day
The user can also set the time of day. Time of day should only need to be set if the battery has been depleted because of extended 
power outages or when daylight saving time begins or ends. If an extended power outage occurs, the time of day will  flash on and 
off which indicates the time of day should be reset. The non rechargeable battery should also be replaced.

Regeneration Mode
Typically a system is set to regenerate at a time of low water usage. An example of a time with 
low water usage is when a household is asleep. If there is a demand for water when the system is 
regenerating, untreated water will be used. 

When the system begins to regenerate, the display will change to include information about the step of the regeneration 
process and the time remaining for that step to be completed. The system runs through the steps automatically and will reset 
itself to provide treated water when the regeneration has been completed.

Manual Regeneration
Sometimes there is a need to regenerate the system sooner than when the 
system calls for it, usually referred to as manual regeneration. There may 
be a period of heavy water usage because
  of guests or a heavy laundry day. 

To initiate a manual regeneration at the preset delayed regeneration time, when the regeneration time option is set to 
“DELAYED REGEN” or “DELAY + IMMEDIATE”, press and release “REGEN”. The words “REGEN TODAY” will 
periodically be shown on the display to indicate that the system will regenerate at the preset delayed regeneration time. If you 
pressed the “REGEN” button in error, pressing the button again will cancel the request. Note: If the regeneration time option 
is set to “IMMEDIATE” there is no set delayed regeneration time so “REGEN TODAY” will not activate if “REGEN” button 
is pressed.

To initiate a manual regeneration immediately, press and hold the “REGEN” button for three seconds. The system will begin 
to regenerate immediately. The request cannot be cancelled.
Note:  For softeners, if brine tank does not contain salt,   Fill with salt and wait at least two hours before regenerating.

Содержание KLEAR FLO II

























Отзывы: