Marley Aquatower Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 24

background image

8

installation

Figure 5

7. Use the adjusting bolts on the motor support to adjust belt tension. A

correctly tensioned belt does not slip when the fan is running—and the
“tight” side is straight between sheaves. The “slack” side will have a slight
bow. If possible, use a commercially available tension measuring device.
Avoid over-tensioning. Too much tension reduces bearing and belt life.
Check the tension on new belts after 8 to 12 hours of operation.

8. Install the belt guard as shown in Figure 3 for a steel tower or Figure 5

for a fiberglass tower.

9. Install fan cylinder splice plate (steel tower) and fan guard.

10. Check bearing housing oil cup level. Fill to the proper level with SAE 30

(ISO 100) weight oil.

3/8" x 1 1/2" BOLT
3/8" WASHERS

USE 3/8" WASHERS TO

SHIM AS REQUIRED

3/8" NEOPRENE WELL-NUT

BELT GUARD FOR FIBERGLASS
AQUATOWER SHOWN

«
...
6
7
8
9
10
...
»

Содержание Aquatower

























Отзывы:

Нет отзывов

Похожие инструкции для Aquatower

Бренд: ZANKER Страницы: 32

Бренд: Indesit Страницы: 12

Бренд: Lincoln Electric Страницы: 21

50gs sizes 018-060

Бренд: Carrier Страницы: 28

Kool-It KGC Series

Бренд: MVP Страницы: 14

FXCA FD620PUREBDF

Бренд: Finlux Страницы: 55

Бренд: Kenmore Страницы: 41

Бренд: Kenmore Страницы: 8

Бренд: Kenmore Страницы: 8

Бренд: Rangemaster Страницы: 40

RSXSDL21 Deluxe

Бренд: Rangemaster Страницы: 56

Бренд: MARYNEN Страницы: 10

Бренд: WC Wood Страницы: 1

Бренд: Lab companion Страницы: 39

Avantgarde Pro KS 90 Series

Бренд: Kaiser Страницы: 80

Бренд: MPM Страницы: 36

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды