background image

25

Shock Sensor Testing Procedure:

Follow the procedure to get into “Remote Feature Programming (Group 3)” mode. Press the (*) button to get

2 Chirps/Beep confirmation. Adjust the sensor with a small flat blade screwdriver to gently turn the sensitivity

screw in the “+” or “–” direction to achieve the desired sensitivity of both zones.
Note 1: Light impacts to the vehicle will activate the “warn-away” stage of the shock sensor. Each time the

warn-away stage is activated, you will hear a short chirp/beep. 

Note 2: A more forceful impact will activate the “alarm trigger” stage of the shock sensor. Each time the alarm

trigger stage is activated, you will hear a long chirp/beep.

Note 3: The shock sensor can be adjusted at any time by entering “Alarm Feature Programming” Part 3 and

following the above directions.

Note 4: If you have (2) sensors installed, set sensor #1 first, then unplug it from the control module. Plug in

sensor #2 and set the sensitivity. When done, plug in sensor #1. 

Turn On the Ignition

3 long chirps and 3 flashes of the parking lights will confirm exit of the

programming mode.
Note: Waiting 15 seconds after the last command will also cause the

system to automatically exit the programming mode.

Step 4: 

Exit Programming

Alarm Feature Programming (Group 3) 

(continued)

Содержание EXTREME X7

































Отзывы: