Market Forge Industries M24E24A Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 31

Market Forge Industries M24E24A Скачать руководство пользователя страница 18

15

APPLICATION INSTRUCTIONS FOR TOTAL CONCEPT CLEANING OF BOILER

SIZE: 1 Gallon PART NUMBER: 20 - 0307

GENERAL NOTES:

Market Forge R has two basic types of boilers; one

has an automatic drain valve, the other has a man-

ual drain valve. To determine which type you have,

open cabinet doors and you will see a control box

with two switches and an indicator light. The instruc

-

tion label on the control box will identify the boiler

as being either automatic or manual. Those boilers

designated as being automatic must be energized

in order to close the drain valve.

Total Concept is designed to be used with water be

-

tween 160°F to 200°F.

Preheating is required on both automatic and man

-

ual boilers to raise the water temperature to the ac

-

ceptable range. (160°F to 200°F).

For manual boilers, make certain drain valve is

tightly closed.

On Market Forged boilers manufactured after 8/84;

your unit is equipped with an access plug in the

steam header line. This location should be used

to add cleaner/descaler to boiler chamber during

maintenance.

On Market Forged boilers manufactured before

8/84; access to boiler chamber should be gained

through either the vent-rite or the pressure relief

valve.

Total Concept is a NSF listed nonfood product. This

is a liquid acid (nonmuriatic) product that works

without fumes, odors, and hazards associated with

other harsh chemicals.

BOILER TREATMENT CLEANING INSTRUC-
TIONS:

After determining proper location for cleaner/des

-

caler to be added: Read complete instructions thor

-

oughly; including all warning and cautionary state

-

ments.

Fig. 1

1

. Energize boiler and fill to operating level.

Fig. 2

2. Energize heating circuit to pre-heat unit.

Fig. 3

Fig. 4

3. AUTOMATIC - After unit is pre-heated, cycle the

power switch to the OFF position then immedi

-

ately back to the ON position.

4. Remove the shipping cap, replace it with the

pouring cap. Cut the tip of the pouring cap at the

first notch to a 45

o

angle.

APPLICATION INSTRUCTIONS

____________________________________________________________________________

«
...
16
17
18
19
20
...
»

Содержание M24E24A
































Отзывы:

Нет отзывов